46.5 kg of fine aggregate is mixed with 72.3 kg of coarse aggregate. The fine aggregate has a moisture content of 2.0% and its absorption is 3.4% whereas the coarse aggregate has a moisture content of 1.3% and its absorption is 3.0%. Determine the amount of water required to increase the moisture content so that there is 1% free moisture in the aggregate blend.

46.5 kg of fine aggregate is mixed with 72.3 kg of coarse aggregate. The fine aggregate has a moisture content of 2.0% and its absorption is 3.4% whereas the coarse aggregate has a moisture content of 1.3% and its absorption is 3.0%. Determine the amount of water required to increase the moisture content so that there is 1% free moisture in the aggregate blend.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter18: Bituminous Materials

Section: Chapter Questions

Problem 8P: Given four different types of aggregates to be used to produce a blended aggregate for use in the...

See similar textbooks

Similar questions

In concrete work, Fuller and Thompson (1907) suggested that a dense packing of grains can be achieved if the percent finer (p) and grain size (D) are related by the following equation, where n is a constant varying in the range of 0.3-0.6. Dmax is the size of the largest grain within the soil. p=(DDmax)n100 This equation is sometimes used in roadwork for selecting the aggregates. a. For n = 0.5, show that the soil is well graded. b. If n = 0.5 and Dmax = 19.0 mm, find the percentages of gravel, sand, and fines within the soil. Use the Unified Soil Classification System.
500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings: 1-Moisture content % is 2- The mass of oven dried sand is
The mass of aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the: (iii)apparent specific gravity, and the (iv) aggregate absorption.
The mass of aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (a) Calculate the: (i) dry bulk specific gravity (ii) SSD bulk specific gravity,
46.5 kg (102.3 lb) of fine aggregate is mixed with 72.3 kg (159.1 lb) of coarse aggregate. The fine aggregate has a moisture content of 2.0% and absorption of 3.4%, whereas the coarse aggregate has a moisture content of 1.3% and absorption of 3.8%. What is the amount of water required to increase the moisture contents of both fine and coarse aggregates to reach absorption? Why is it important to determine the amount of water required to increase the moisture content of aggregate to reach absorption? Use one system of units only as specified by the instructor.
The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2. (e) Calculate the dry bulk specific gravity, SSD bulk specific gravity, apparent specific gravity, and the aggregate absorption.
500 gm oven dry fine aggregate was tested to find its physical properties. The output from the test was as follows: SSD = 510 gm, mass of the vessel full of water = 1200 gm, mass of vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm, Apparent specific gravity= 2.5 . The grading of the fine aggregate is in the table below. Answer the followings: 1- The fineness modulus (F.M) is 2- The bulk specific gravity is 3- Absorption% is 4- Moisture content % is 5- The mass of oven dried sand is
Use the following data:Oven Dry weight - 4.98 kgWeight under water - 3.02 kgSSD Weight - 5.07 kg1. Determine the apparent specific gravity of the coarse aggregates.2.Determine the bulk specific gravity SSD of the coarse aggregates3.Determine the bulk specific gravity (Dry) of the coarse aggregates4.
A mix design requires 1160 kg/m3 of coarse aggregate (in dry condition), 599 kg/m3of fine aggregate (in dry condition) and 148 kg/m3 of water. The absorption capacityof the coarse aggregate is 0.4 % while the moisture content is 1.5%. The absorptioncapacity of the fine aggregate is 0.4 % while the moisture content is 4%. Pleaseanswer the following questions based on information given. a. What is the amount of Moist Coarse Aggregate? b. What is the amount of SSD Fine Aggregate? c. What is the amount of Moist Fine Aggregate? d. What is the amount of water after adjusting for moisture?
For concrete production, we mix 625 kg of fine aggregate and 830 kg of coarse aggregate. The fine aggregate has a moisture content of 2.3% and absorption of 3.2%, whereas the coarse aggregate has a moisture content of 1.5% and absorption of 2.8%. Calculate the amount of water required to increase the moisture contents of both fine and coarse aggregate to reach absorption?
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows:Aggregate A: Bulk specific gravity = 2.491; absorption = 0.8,Aggregate B: Bulk specific gravity = 2.773; absorption = 4.6,a. What is the specific gravity of a mixture of 60% aggregate A and 40% aggregate B by weight?b. What is the absorption of the mixture?
1000 g coarse aggregate sample taken from the site showed the following properties in the laboratory. Oven-dry weight: 971 g, SSD weight: 1003 g, Weight in water: 627 g Calculate the a) dry and SSD bulk specific gravity b) moisture content and c) absorption capacity of the aggregate.