Question
5. Analyze the statically indeterminate beam by force method, and draw the bending
moment diagram, assume that El is constant.
40kN
3m
3m
6m
Expand
Transcribed Image Text

5. Analyze the statically indeterminate beam by force method, and draw the bending moment diagram, assume that El is constant. 40kN 3m 3m 6m

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Solid Mechanics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: At room temperature (20°C) a 0.5-mm gap exists between the ends of the rods shown in the figure. At ...

A: For aluminum ;A1=2000 mm2=2×103×10-6 m=2×10-3 m ;E1=75 GPa=75×106 kPa ;α1=23×10-6 /°C ;L01=300 mm=0....

Q: Need help figuring out this Pressure/Temperature question: A cylinder that has a 41.5-cm radius and ...

A: Calculate the area of the piston. A=πr2 Here, A is the area of the piston, and r is the radius of th...

Q: please check attach file

A: Given:P1=3 MPaT1=400οCV1=70msP2=20 KPaV1=40msDryness fraction,x=0.93

Q: Zinc crystallizes in HCP structure. Geometrically the height of the unit cell is       ...

A: D) The fourth option (data insufficient) is correct.

Q: If the compressor and condenser fan motor will not operate but the indoor fan motor is operating, wh...

A: The circuit diagram for given question can be shown as.

Q: Please check attach file

A: Given Data The solid shaft diameter d=240mm The outer diameter of hollow shaft=d0=240mm Allowable sh...

Q: Determine the following given the figure below: a. Equivalent stiffness b. Angular frequency c. Natu...

A: Givena=40 cm = 0.4 m b=80 cm =0.8 m L= 120 cm =1.2 mFor a simply supported beam with point load on t...

Q: Please answer the following question

A: Given: The mass flow rate of steam is m=1.2 kg/s. The exit velocity of steam from nozzle is V=220 m/...

Q: A wing component on an aircraft is fabricated from an aluminum alloy that has a plane strain fractur...

A: Dimensionless geometry factor can be determined by using equation of stress intensity factor

Q: For the beam shown, determine the reaction at B.

A: Portion AC: yc=Mc(L/2)22EI-Vc(L/2)33EIyc=Mc(L)28EI-Vc(L)324EIθc=Mc(L/2)EI-Vc(L/2)22EIθc=Mc(L)2EI-Vc(...

Q: By swimming with fins, you manage to take a beach ball to the bottom of a pool. Once the beach ball ...

A: Archimedes principle: Whenever a body is fully or partially immersed in the fluid, it is subjected t...

Q: A lead sphere has volume 6.0 cm3 when it is resting on a lab table, where the pressure applied to th...

A: Click to see the answer

Q: Choose the corect answer -A vertical line in the phase diagram represents  a.an intermetallic compo...

A: Phase Diagram :- A phase diagram in material science is a type of chart which shows material conditi...

Q: What is the failure due to fatigue? What factors influence the fatigue strength of the material? Und...

A: Fatigue failure is the formation of cracks due to repetitive load which results in the damage of the...

Q: 8. For hydraulic pumps and motors, there are two types of losses, i.e._

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: E. There are two states for fluid flow, i.e. laminar flow and nd the state can be determined by_ . T...

A: 5. The two states of fluid flow are laminar flow and turbulent flow. The turbulent flow is also know...

Q: Why is friction generally undesirable in metal forming operations?

A: Metal forming is the type of manufacturing process in which the metal undergoes plastic deformation ...

Q: Differentiate between thermal conductivity and thermal conductance of a material

A: Thermal conductivity It is the ability of a material to conduct heat. It represents by K.  (It is a ...

Q: Write the advantages and disadvantages of V-belt drive over Flat belt drives

A: The advantages of V-belt drive over flat belt drives are as follows. Since V-belts are prepared end...

Q: Compare the differences between different gear profiles

A: There are two types of gear profiles are present (i) Cycloidal profile (ii) Involute profile

Q: Determine the magnitude of the moment of the 500N force about point 0. Express you answer in Nm; uni...

A: Moment is basically defined as product of force and perpendicular distance from point to line of act...

Q: A 3.1 meter ladder with a mass of 24 kg rests against a wall. Neglect the friction between the ladde...

A: Length of the ladder is 3.1 m Mass of the ladder is 24 kg Angle made by the ladder with the wall is ...

Q: Describe and account for the width and tread pattern in a racing car tyre when compared to that of a...

A: Solution: