5.5-5 Beam ABC has simple supports at A and B and an overhang from B to C. The beam is constructed from a steel IPN 400 shape. The beam must carry its own weight in addition to uniform load q = 2.2 kN/m. Determine the maximum tensile and compressive %3D stresses in the beam.

5.5-5 Beam ABC has simple supports at A and B and an overhang from B to C. The beam is constructed from a steel IPN 400 shape. The beam must carry its own weight in addition to uniform load q = 2.2 kN/m. Determine the maximum tensile and compressive %3D stresses in the beam.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.5.5P: Beam ABC has simple supports at A and B and an overhang from B to C. The beam is constructed from a...

See similar textbooks

Related questions

Q: 3) On a structural steel I profile beam a distributed load and M moment is applied as shown in the…

A: Youngs modulus E = 200 GPa Length, L = 1 m Moment, M = 245 N-m Cross section dimensions h = 145 mm b…

Q: On a structural steel I profile beam a distributed load and M moment is applied as shown in the…

A: Given data On a structural steel I profile beam a distributed load and M moment is applied as shown…

Q: The concrete table column-support in Problem 20is reinforced with three -in steel rods, as shown in…

Q: For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at…

Q: Problem C-3 [Beam Bending - Normal Stress] A simply supported beam (i.e., with a pin support at…

Q: 3) On a structural steel I profile beam a distributed load and M moment is applied as shown in the…

A: Youngs modulus E = 200 GPa Length, L = 1 m Moment, M = 245 N-m Cross section dimensions h = 145 mm b…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 3.75w…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: A member has the triangular cross section shown in the figure below. 4 in. 4 in. M -2 in.2 in.…

A: Data given- Allowable tensile stress = 22 ksi Allowable compressive stress = 16 ksi

Q: A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded at…

A: Given data:

Q: A beam of rectangular cross-section is 64 mm broad, 100 mm deep, and 1.6 m long. It is simply…

A: Given that, Length of beam, L=1.6 m,Breadth of beam, b=64 mm,Depth of beam, d=100 mm,Load at the mid…

Q: 3 KN/m D B 120 mm YA= 40 mm A. 80 mm 1m 2 m 10 KN 10 KN L= 4 m

Q: 6.2-2 A wood beam is strengthened using two steel plates as shown in Fig. a. The beam has simple…

A: Given, Youngs modulus of wood, EW=11GPa. Youngs modulus of steel, ES=200GPa The moment of inertia of…

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: σpi=11 mPa Epi=8 GPaσpl=14 mPa Epl=12 GPaFind allowable magnitude w=?

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: Answer: (a) The maximum tension bending stress is 1530.2124 psi. (b) The maximum compression bending…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: 4. A stepped bar is subjected to an axial tensile force of 40000 lb. Compute the increase in stress…

Q: The figure below shown that the three bars are supported a rigid beam ACE. ar CD is made of steel…

A: Given data, d= diameter of each bar =10 mm σAl=allowable stress for aluminum=120 MPa σsteel=…

Q: 1. A simply supported 8m span beam with a uniform distributed load of 90KN/m over its entire span,…

Q: (a) A steel cantilever beam with a 1-in-diameter round cross section and length of 10 in is loaded…

A: A machine member is subjected to various forces. Depending on these forces and points of loading the…

Q: A bending moment of M=150 kips in is applied at the cross section of bearn shown in Figure Question…

A: Answer: ◆ The maximum tensile stress is 9.57568 ksi. ◆ The maximum compressive stress is 14.91330…

Q: Installed appointment of a beam made of a U profile in the figure Find the length c of the overhangs…

A: FBD of given fig. Finding reactionRA+RB=30+30 +40×6RA+RB=300KnSo RA=RB=3002=150Kn

Q: A thin-walledbeam of hollow circular cross-section shown below is subject to both torsional and…

A: Given data: The outer diameter, do = 100 mm. The thickness of the wall, t = 5 mm. The bending…

Q: Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

Q: Consider the beam shown in sketch below, hinge supported at point A and roller supported at point D.…

A: Considering the cross-section of the beam The web is denoted as 1 and flange is denoted as 2

Q: . Determine the shear stresses along sections A-A, B-B, C-C and D-D. b. Plot the shear stress…

Q: 5.5-18 Determine the maximum tensile stress o, and maximum compressive stress o due to the load P…

Q: A thin-walled cylindrical pressure vessel of radius r is subjected simultaneously to internal gas…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

Q: A Simply Supported beam of 4 m span is in the form of hollow square bar (120x120 mm) as shown in…

Q: In the ship crane in the figure, at the D and A supports, Find the reaction forces. Section area…

Q: Example (5.3): Find the maximum tensile and compressive stresses for the beam shown in Figure (5.6).…

Q: A round beam of length 14-in is simply supported at A and D. The beam is loaded in torsion and with…

Q: The horizontal beam AB of 1.8-2 cross-sectional dimensions (b x h = 19 mm x 200 mm) is supported by…

Q: Q5/ A rectangle RC beam is reinforced with 5 Ø16mm in the tension zone as shown in Figure 4. Check…

Q: HOMEWORK: Q1/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa…

A: Find load P

Q: As shown in Fig. 4, a steel frame with Young's modulus E-203 GPa and Poisson's rat v-0.3 is…

A: GivenE=203GPaν=0.3Ro=25cm=0.25mRi=15cm=0.15mt=5cm=0.05m

Q: The figure below shows a simply supported prismatic beam with an applied uniform load. The labeled…

A: let length of the beam is L All points are equally spaced therefore space between two points are L4…

Q: A copper column of annular cross section has an outer diameter of 5m and is subjected to an axial…

A: Given Outer diameter of column do=5 m Axial load applied P=200 kN Allowable compressive stress…

Q: 3.03 The beam shown below is an aluminum channel, C 100 x 50 x 25.79, positioned with the legs down…

A: Given: The channel width, b = 100 mm The channel height, h = 50 mm The web thickness, t = 25.79 mm

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A: Given Data: Length of the beam, L=16 ft

Q: 3) On a structural steel I profile beam a distributed load and M moment is applied as shown in the…

A: Importing the part from catia to the ANSYS 5.0 student version as per requirement

Q: A simply supported wide-flange beam of span length L carries a vertical concentrated load P acting…

Q: An L-shaped bracket lying in a horizontal plane supports a load P =1501b (see figure). The bracket…

A: Given Data The load acting at the support is: P=150 lb The thickness is: t=0.125 in The breadth is:…

Q: 40 men D Steel t-200 GPa The rigid beam (ABC) supported by three bars, One from the top and two from…

Q: Figure 4 shows a rigid beam ABC supported b A load P=13.5 kN is applied at C. Diameter of wall of…

Q: In the ship crane in the figure, at the D and A supports, Find the reaction forces. Section area…

Q: 4: - The Inverted T section of a L-m simply supported beam has the properties shown in Fig. (4).…

Q: LA rod is composed of aluminum section with diameter of 25mm is rigidly attached between hallow…

Question

Solution plzzzzz!!

5.5-5 Beam ABC has simple supports at A and B
and an overhang from B to C. The beam is constructed
from a steel IPN 400 shape. The beam must carry
its
own weight in addition to uniform load q = 2.2 kN/m.
Determine the maximum tensile and compressive
%3D
stresses in the beam.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Beam ACE hangs from two springs, as shown in the figure. The springs have stiffnesses kxand k2and the beam has flex lira I rigidity EL (a) What is the downward displacement of point C, which is at the midpoint of the beam, when the moment M0 is applied? Data for the structure are as follows: M0= 10,0 kN m, L = 1.8 m, EI = 216 kN m2, Jt, = 250 kN/m, and k2= 160 kN/m, (b) Repeat part (a), but remove A/() and apply a uniform load q — 3.5 kN/m to the entire beam.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
Solve the preceding problem using the following data: beam cross section is 100 x 150 mm, length is 3 m, and point load is P = 5 kN at mid-span, Point C is located 25 mm below the top of the beam and 0.5 m to the right of support A.
A beam ABC with an overhang from B to C is constructed of a C 10 × 30 channel section with flanges facing upward (sec figure). The beam supports its own weight (30 lb/ft) plus a triangular load of maximum intensity g0 acting on the overhang. The allowable stresses in tension and compression arc IS ksi and 12 ksi, respectively. Determine the allowable triangular load intensity allow if tne distance L equals 4 ft. What is the allowable triangular load intensity fallow ^tnc Dcam is rotated 180e about its longitudinal centroidal axis so that the flanges are downward?
A beam A BCD rests on simple supports at B and C (see figure). The beam has a slight initial curvature so that end A is 18 mm above the elevation of the supports and end D is 12 mm above. What moments Mtand M^, acting at points A and Dtrespectively, will move points A and D downward to the level of the supports? (The flexural rigidity EI of the beam is 2.5 X 106 N m2 and L = 2.5m).
Beam ABC has simple supports at A and B and an overhang from B to C. The beam is constructed from a steel W 16 × 3L The beam must carry its own weight in addition to uniform load q = 150 lb/ft. Determine the maxima m tensile and compressive stresses in the beam.
Solve the preceding problem for a box beam with dimensions h — 200 mm, A, = 160 mm, b = 150 mm, and A, =130 mm. Assume that the beam is constructed of steel with yield stress eY= 220 MPa.
A cantilever beam A3, loaded by a uniform load and a concentrated load (sec figure), is constructed of a channel section. (a) Find the maximum tensile stresser, and maxi-mum compressive stress trcif the cross section has the dimensions indicated and the moment of inertia about the - axis (the neutral axis) is t = 3.36 in4. Note: The uniform load represents the weight of the beam. Find the maximum value of the concentrated load if the maximum tensile stress cannot exceed 4 ksi and the maximum compressive stress is limited to 14.5 ksi. How far from A can load P = 250 lb be positioned if the maximum tensile stress cannot exceed 4 ksi and the maximum compressive stress is limited to 14.5 ksi?
A cantilever beam, a C12 x 30 section, is subjected to its own weight and a point load at B. Find the maximum permissible value of load f at B (kips) if the allowable stress in tension and compression is o\. =18 ksi.
The wing of a large commercial jet is represented by a simplified prismatic cantilever beam model with uniform load \v and concentrated loads P at the two engine locations (see figure). Find expressions for the tip deflection and rotation at D in terms of \\\ P, L, and EL.
A wood beam AB with a rectangular cross section (4 in. × 6 in.) serving as a roof purlin is simply supported by the top chords of two adjacent roof trusses. The beam is subjected to distributed load q acting in the vertical direction through the centroid of the purlin cross section. The top chords of the trusses have a slope of = 27°. The purlin has length L =75 in. Determine the permissible distributed load q based on the allowable compressive and tensile stress in the beam eall = 2 ksi.
A simple beam AB is loaded as shown in the figure. Calculate the required section modulus S if ^aibw = IS,000 psi, L = 32 ft, P = 2900 lb, and g = 450 lb/ft. Then select a suitable I-beam (S shape) from Table F-2(a), Appendix F, and recalculate 5 taking into account the weight of the beam. Select a new beam size if necessary. What is the maximum load P that can be applied to your final beam selection in part (a)?