6 The circuit shown in Figure P7.16 is to be used ontwo different sources, each with the same amplitudebut at different frequencies.a. Find the instantaneous real and reactive power ifvs(t) = 120 cos 377t V (1.e., the frequency is 60 Hz).b. Find the instantaneous real and reactive power ifvs(t) = 650 cos 314t V (i.e., the frequency is 50 Hz). C= 265 µFL= 25.55 mHR = 10 2

Write the expression to find the equivalent impedance of the circuit.

Answered: 6 The circuit shown in Figure P7.16 is…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula that relates three-phase apparent power to active and reactive power. 3. Draw a graph that depict single-phase waveforms for a purely sinusoidal 50 Hz voltage and a lagging current.
For the circuit shown in Figure P7.43, assume thatvg = 120 V rms. Finda. The total resistance seen by the voltage source.b. The primary current.c. The primary power.
The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Explain the concept of power quality and the various disturbances that can affect it, such as harmonics and transients.
Analyze the impact of harmonics in power systems and propose mitigation techniques.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3.and ??Find the value of the maximum average power transferred to?
An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the operating voltage is 4800 V at 60 Hz. What should be done to bring the power factor to 0.95 in lagging? Indicate what you would connect and with what three-phase power. If the connection of the element to be added is in delta, indicate its reactance and the value of its capacitance or inductance. capacitance or inductance.
The 9 Ω resistor in the circuit is replaced with a variable impedance Zo. Assume Zo is adjusted for maximum average power transfer to Zo. 1. a) What is the maximum average power that can be delivered toZo?2. b) What is the average power developed by the ideal voltage sourcewhen maximum average power is delivered to Zo?3. c) Choose single components from Appendix H to form animpedance that dissipates average power closest to the value in part(a). Assume the source frequency is 60 Hz.
Find the apparent power and the real powerdelivered to the load in the Y-Δ circuit shown in FigureP7.74. What is the power factor? Assume rms values
Calculate the rms values of load voltage and current for the circuit shown below. Please show work

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning