6. A simple air cooled system is used for an aeroplane to take a load of 10 tons. Atmospheric temperature and is 25°C and 0.9 atm respectively. Due to ramming the pressure of air is increased from 0.9 atm. to 1 atm. The pressure of air leaving the main compressor is 3.5 atm and its 50% heat is removed in the air-cooled heat exchanger and then it is passed through a evaporator for future cooling. The temperature of air is reduced by 10°C in the evaporator. Lastly the air is passed through cooling turbine and is supplied to the cooling cabin where the pressure is 1.03 atm. Assuming isentropic efficiency of the compressor and turbine are 75% and 70%, find a) Power required to take the load in the cooling cabin b) COP of the system. The temperature of air leaving the cabin should not exceed 25°C. pressure

6. A simple air cooled system is used for an aeroplane to take a load of 10 tons. Atmospheric temperature and is 25°C and 0.9 atm respectively. Due to ramming the pressure of air is increased from 0.9 atm. to 1 atm. The pressure of air leaving the main compressor is 3.5 atm and its 50% heat is removed in the air-cooled heat exchanger and then it is passed through a evaporator for future cooling. The temperature of air is reduced by 10°C in the evaporator. Lastly the air is passed through cooling turbine and is supplied to the cooling cabin where the pressure is 1.03 atm. Assuming isentropic efficiency of the compressor and turbine are 75% and 70%, find a) Power required to take the load in the cooling cabin b) COP of the system. The temperature of air leaving the cabin should not exceed 25°C. pressure

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter48: Cooling Towers And Pumps

Section: Chapter Questions

Problem 13RQ

See similar textbooks

Similar questions

If 14 gpm of water is flowing through an open-loop heat pump with a temperature difference of 7F, how much heat in Btu/h is being absorbed or rejected in the heat pump? Show all work and units.
The most popular refrigerant used in the past for residential air-conditioning is R- ________.
The device that relieves the pressure in a boiler when it is above the design working pressure is the ________valve.
Static electricity is more commonly a problem when the air is_________. A. dry B. moist
Define temperature glide, and give examples of where it occurs in a refrigeration system.
The function of the pressure tank in an open-loop, geo-thermal heat pump well system is to prevent the well pump from _____.
What is the heat output, in Btu/h, of a terminal unit with a T of 10F and a water flow rate of 5 gpm?
Three advantages of unitary, stand-alone refrigeration modules in supermarket refrigeration are ______and _______.
The catalogue for a refrigerant 22, four-cylinder, hermetic compressor operating at 29 r/s. a condensing temperature of 40 °C and an evaporating temperature of -4 °C shows a refrigeration capacity of 96.4 kW. At this operating points the motor (whose efficiency is 90 percent) draws 28.9 kW. The bore of the cylinders is 87 mm and the piston stroke is 70 mm. The performance data are based on 8 °C of subcooling of the liquid leaving the condenser. Compute 3.1 the actual volumetric efficiency and 3.2 the compression efficiency.
. A simple air cooled system is used for an aeroplane to take a load of 10 tons. Atmospheric temperature and pressure is 25°C and 0.9 atm respectively. Due to ramming the pressure of air is increased from 0.9 atm, to 1 atm. The pressure of air leaving the main compressor is 3.5 atm and its 50% heat is removed in the air-cooled heat exchanger and then it is passed through a evaporator for future cooling. The temperature of air is reduced by 10°C in the evaporator. Lastly the air is passed through cooling turbine and is supplied to the cooling cabin where the pressure is 1.03 atm. Assuming isentropic efficiency of the compressor and turbine are 75% and 70%, finda) Power required to take the load in the cooling cabinb) COP of the system.The temperature of air leaving the cabin should not exceed 25°C.
An 500-HP engine with a thermal efficiency of 30% is using a remote radiator which absorbs 20% of the heat supplied to the engine. Cooling system with cooling tower is used with a cooling range of 5°C. The temperature rise after passing the remote radiator is 10°C. Air enters the cooling tower at 30°C dry-bulb; 20°C wet-bulb temperatures and leaves the tower at 38°C & 65%RH. Make a schematic diagram of the system, the process in the provided psychrometric chart and calculate the following: (a.) The amount of cooling water for the engine, kg/min; (b.) The water flow rate in the cooling tower in liters per hour; and (c.) If the heat absorbed by air is 5% of heat absorbed by the cooling tower water, what is the air flow needed in cu.m/hour.
A simple air cooled system is used for an aero plane to take a load of 10 tons.Atmospheric temperature and pressure is 25°C and 0.9 atm respectively. Dueto ramming the pressure of air is increased from 0.9 atm, to 1 atm. The pressureof air leaving the main compressor is 3.5 atm and its 50% heat is removed inthe air-cooled heat exchanger and then it is passed through a evaporator for future cooling. The temperature of air is reduced by 10°C in the evaporator.Lastly the air is passed through cooling turbine and is supplied to the coolingcabin where the pressure is 1.03 atm. Assuming isentropic efficiency of the compressor and turbine are 75% and 70%,find i) Power required to take the load in the cooling cabinii) COP of the system.The temperature of air leaving the cabin should not exceed 25°C