6 and 7 please 6. Determine the horizontal and vertical components of force which the pins at A,B, and C exert on memberABC of the frame.400 NF1.5 m-2 m1.5m2.5 m300 N300 NAnswer:2.5 mB. = 0, By = 428.5 N15m7. Determine the maximum tension in the cable shown.20 m2.4 m AAnswer:1.5 mtBTA = 34.64 kN1500 N/mNIVERSITYICALN

Answered: Image /qna-images/answer/b3db3b66-eae0-419e-b77c-403c41e87e99.jpg

6. Determine the horizontal and vertical components of force which the pins at B, and C exert on member ABC of the frame. 400 N 1.5 m- -2 m 1.5m 2.5 m 300 N 300 N Answer: 2.5 m В. 3D 0, В, %3D 428.5 N 1.5 m 7. Determine the maximum tension in the cable shown. 20 m 2.4 m A Answer: 1.5 m B TA = 34.64 kN 1500 N/m UNIVERSITY ITICALA

6. Determine the horizontal and vertical components of force which the pins at B, and C exert on member ABC of the frame. 400 N 1.5 m- -2 m 1.5m 2.5 m 300 N 300 N Answer: 2.5 m В. 3D 0, В, %3D 428.5 N 1.5 m 7. Determine the maximum tension in the cable shown. 20 m 2.4 m A Answer: 1.5 m B TA = 34.64 kN 1500 N/m UNIVERSITY ITICALA

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13. A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE and BF as shown in Figure 2. Knowing that the tension in cable CD is 14 KN and assuming that CD is parallel to the x-axis (0), determine the horizontal component of the reaction at A. A. 7.00 kN B. 17.50 kN C. 22.4 kN D. 2.50 kN
The tongs are used to grip the ends of the drillingpipe P. If a torque (moment) of MP = 800 lb ⋅ ft is neededat P to turn the pipe, determine the cable force F that mustbe applied to the tongs. Set θ = 30°.
P1 = 3.9 kN, P2 = 6.3 kN a) Determine the force P needed to hold the cable in the position shown, so segment BC remains horizontal b) compute sag yB. c) compute the maximum tension in the cable.
Solve Prob. 3.53 when the tension in cable AB is 306 lb
The cables in Figure P6.7 have been dimensionedso that a 3-kip tension force develops in each verticalstrand when the main cables are tensioned. What valueof jacking force T must be applied at supports B and C totension the system? Show the diagram.
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.
Compute for support reactions and maximim tension in the cable.
A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are placed such that approximately loads the cable by a uniform q(x) = q0. If l (small letter L) = 10 m, hA = 5 m, and hB = 4 m. Compute the maximum force in the cable for its minimum distance to the group by 3 m. q0 (kN/m) 12.213
Determine the tension in cable BD if P = 51 N.
The boom supports the two vertical loads. Neglect the size of the collars at D and B and the thickness of the boom, and compute the horizontal and vertical components of force at the pin A and the force in cable CB. SetF1 = 800 N and F2 = 350 N.
Two cables are tied together at C and are loaded as shown. Knowing that P = 4386, α = 44° and θ = 66.3°, determine the tension in cable BC
The top end of vertical boot is connected by two cables having tension T1=500N and T2=1500N as shown in the figure. The third cable AB is used as a guy wire. Determine the tension in cable AB if resultant of three concurrent forces acting at A is vertical?