9 Adiode with the i-v characteristic shown in Figure 9.8 in the text is connected in series with a 5-V voltage source (in the forward bias direction) and a load resistance of 200 2. Determine a. The load current and voltage. b. The power dissipated by the diode. c. The load current and voltage if the load is changed to 100 2 and 500 s2. Diode i-v curve 50 40. 30. 20. 10. 0.2 0.4 0.6 Diode voltage, V 0.8 1.0 Diode current, mA

9 Adiode with the i-v characteristic shown in Figure 9.8 in the text is connected in series with a 5-V voltage source (in the forward bias direction) and a load resistance of 200 2. Determine a. The load current and voltage. b. The power dissipated by the diode. c. The load current and voltage if the load is changed to 100 2 and 500 s2. Diode i-v curve 50 40. 30. 20. 10. 0.2 0.4 0.6 Diode voltage, V 0.8 1.0 Diode current, mA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

Consider a peak rectifier ted by a 50 Hz sinusoid having a peak value Vp-100 V. Let the load resistance R 10 kohm. The value of the capacitance C that will result in a peak to peak ripple of 3 V is:
Consider the voltage regulator shown in Figure P9.28. The source voltage Vs varies from 10 to 14 V, and the load current iL varies from 50 to 100 mA. Assume that the Zener diode is ideal. Determine the largest value allowed for the resistance Rs so that the load voltage vL remains constant with variations in load current and source voltage. Determine the maximum power dissipation in Rs.
What is the zener diode and what are its advantages? In what region of their characteristic curve are zener diodes operated? At what value of zener current is the zener voltage normally specified? How does the zener impedance affect the voltage across the terminals of the device?
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
please solve parts d and e Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise? d) Determine the input power (active)? e) Determine the power factor?
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
Sketch i versus v to scale for the circuits shown in Figure P9.6. The reverse-breakdown voltages of the Zener diodes are shown. Assume voltages of 0.6 V for all diodes including the Zener diodes when current flows in the forward direction.
Design a half-wave rectifier power supply to deliver an average voltage of 9 V with a peak-to-peak ripple of 2 V to a load. The average load current is 100 mA. Assume that ideal diodes and 60-Hz ac voltage sources of any amplitudes needed are available. Draw the circuit diagram for your design. Specify the values of all components used. Repeat Problem P9.54 with a full-wave bridge rectifier.
Figure shows an AC source G having an effective voltage of 240 V, 60 Hz is connected to a single-phase full-wave rectifier. The resistance for R is 53 Ω and ripple-to-ripple current is 15%.Determine the DC voltage and DC current across the resistor. Hence, determine the power absorbed by the load. Assuming all diodes are ideal.
Draw the circuit diagram of a single phase full-wave uncontrolledrectifier with R-load. Describe its principle of operation. Draw thewaveforms of: input voltage, voltage across the load, current throughthe diodes and their voltage. Write the expressions for: the averageoutput voltage Vd, the maximum reverse voltage across the diode and thestandard transformer power. Describe what the difference will be if acapacitor is added in parallel with the load at the output.
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
Below is a circuit containing a non-linear element;a) Determine the operating points (two) of the circuit in DC state?b) Find the resistance equivalent of the nonlinear element for the operating points you specified?c) For AC welding, find the instantaneous power of the nonlinear element (considering the element's equivalent resistance at the operating point)?