___________ tool is used for verifying the flatness of the component.     A. Protractor     B. Engineer square     C. Micrometer     D. Spirit leveler

Q: Carriage is mounted on the outer guide ways of lathe bed and it can move in a direction parallel to…

A:

Q: Answer the following questions by circling True or False. 1. Capstan and turret lathes utilise many…

A: 1) Both the lathes utilizes many tools. 2) Lead screw converts rotary motion to linear motion. 3)…

Q: In surface grinder, for ferrous metals __________accessory is used.

A: In surface grinder, for ferrous metals __________accessory is used. Answer: A. Magnetic chuck

Q: machine elements question about shafts

A:

Q: It carries the cutting tool and precisely controls its movement either parallel to the ways ,called…

A: Option d is correct.

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: Which of the following tools is essential in sheet metal job but not in a fitting job? A. Steel…

A: Steel ruler- it is a measuring tool to measure the linear dimensions. It is used in fitting job.…

Q: If the grade on the grinding wheel used for grinding operation in the workshop is denoted by "E",…

A:

Q: If the grade on the grinding wheel used for grinding operation in the workshop is denoted by "T",…

A: As per given question  If the grade on the grinding wheel used for grinding operation in the…

Q: If the grade  on the grinding wheel used for grinding operation in the workshop is denoted by  "T",…

A: If the grade  on the grinding wheel used for grinding operation in the workshop is denoted by  "T",…

Q: 18 A typical lathe bed is made of a low grade cast iron. Select one: True False

A: We have to find  true /false A typical lathe bed is made of a low grade cast iron.

Q: the reading of this tool is

A:

Q: The angle of forst of c

A: Given; From given figure: A stepped shaft subjected to a twisting moment applied at BShear modulus…

Q: Which of the following is the correct order of doing a fitting job? B. Clamping on vice- Marking…

A: The correct order of doing a fitting job is,

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: If the grade on the grinding wheel used for grinding operation in the workshop is denoted by "L",…

A:

Q: b) With a neat sketch differentiate between boring and tapping operation.

A: This question is from manufacturing engineering.  We have to define boring and tapping operation.

Q: 17q In a lathe machine tool, when the cutting tool moves perpendicular to the axis of rotation of…

A: Lathe machine: Lathe machine is device which used to remove the material from workpiece. By removing…

Q: Lathe Machine tool is an example of three axes machines

A: Lathes, by definition, are 2-axis machines. Once machines advanced to incorporate 3-axis, 4-axis…

Q: A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further…

A: A lathe mandrel is a hardened and tempered steel work-holding device.it is used for the further…

Q: What are different parts of an excavator (briefly discuss any five)?

A: The different part of excavator are:- Bucket Arm Hydraulic cylinder Boom Cab Engine Counterweight…

Q: What type of tool is not used in semi-precision layout?   a)Plain protractor b)Surface gage…

A: Given :-  What type of tool is not used in semi-precision layout?   a)Plain protractor…

Q: Which machining procedure cannot create cylindrical surface?   a. reaming b. head sinking c. thread…

A: Slot milling is the milling process in which Slot are created on the surface of material.

Q: It is a fixed casting attached to the back of the lathe carriage (a) Collet attachment (b)Magnetic…

A:

Q: The required shape of the Tipped type tool is made by forging before hardening and grinding high…

A: The process that is used to provide the required shape is basically the powdered metallurgy process.…

Q: Which of the following is the correct order of doing a fitting Job C. Marking -Filing - Surface…

A: First step of fitting job is marking then we can clamp the object in the vice so that material…

Q: differentiate between caption and turret lathe

A: Capstan and Turret lathe is one of the broad classifications of a Lathe

Q: 9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid…

A:

Q: During operating lathe machine, the tool bit should be fixed as short as possible. Select one: True…

A: The given statement is true.

Q: In lathe machine, Work piece is held in the work holding device called ‘Chuck’ and the chuck is…

A: cross slide has tool post mounted on that so wrong  tail stocks is used for support the wok piece so…

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is On…

A: The engine lathe is a high-precision machine tool that needs to be treated with care. The lathe's…

Q: Drilling operation to produce conical shape on a drilled hole is known as a. Boring b. Counter…

A:

Q: lathe machine has a constant failure rate and a mean time to failure of 10 years. What is the…

A:

Q: Describe and sketch open drill jigs with its components

A: Open type jig , in which the top plate is arrange to swing about a fulcrum point , so that it is…

Q: Angle of bite in radian ?

A: Given data; Single pass rolling process;  Diameter, d=420 mm  Width, b=145 mm  Thickness,t=9 mm…

Q: of drill

A:

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: _________ is a massive and rigid single piece casting made to support other active parts of a lathe…

A: The Answer is option [D] Bed.

Q: Q#01 : Differentiate between (i) Plain Turning and Facing operation (ii)Taper Turning and Knurling…

A: (i) The process of reducing the diameter of a rotating workpiece by providing a definite depth of…

Q: equal par machine is

A:

Q: please provide the following: speed rate, deep of cut and measurements of a meat mallet

A: Machining is a controlled material-removal technique that cuts a material (typically metal) to a…

Q: IDENTIFICATION 1. It is a hardened steal instrument having parallel rows of cutting edged or teeth…

A: 1. File- it is a cutting tool with hardened cutting edges in parallel configuration. It is use in…

Q: 13. What is the size specification of the angle iron below? his uge .1 ine being fy 3" 16 13" 16 14.…

A: as per bartleby guidelines only solution to first question i.e. question no. 13 is given here. here…

Q: In drilling operation on lathe machine, the drill bit is fixed in _______. a. Tool post b. Carriage…

A: Ans_ D_ Tailstock

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is The…

A: Given: The wrong maintenance procedure followed while performing gib adjustment on a lathe machineis

Q: At what rpm should the lathe revolve to rough turn a piece of cast iron (CS = 60 SFPM) 51 mm in…

A: Question: At what rpm should the lathe revolve to rough turn a piece of cast iron

Q: entify the part of a lathe machine which is used to take the cutting forces and vibrations during…

A: GIVEN: Identify the part of a lathe machine which is used to take the cutting forces and vibrations…

Q: ) Explain the following parts of a Lathe machine. i) Carriage ii) Cross slide iii) Tailstock b)…

A: Solution A:    Carriage: It has different parts that are used to support, move and control the…

Q: Which of the following is the correct sequence of the ability of the machining process to produce…

A: There are many processes which are used to get better surface finish. The type of machining process…