Answered: A 15-hp (shaft) pump is used to raise…

A 15-hp (shaft) pump is used to raise water to a 42-m higher elevation. If the mechanical efficiency of the pump is 82%, determine the maximum volume flow of water.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Related questions

Q: Consider two hydraulic turbines having identical specific speed and effective head at the inlet. If…

A: Given data: - The speed ratio of the two turbines is N1/N2 = 2. The expression for the specific…

Q: Ex. 1.13] A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure.…

Q: A mechanical device pumps the fluid from a depth of 150 m under steady conditions. The density of…

A: Given data depth=150m density of fluid=1020 kg/m2 efficiency =70% velocity of fluid =150m/s…

Q: What are the frictional losses to be considered when calculating power consumption of a pump under…

A: The following are the losses to be considered in a pump - 1. The head loss in the suction pipe of…

Q: A hydraulic turbine generator was installed at a site 101 m below the free surface of a large water…

A: Given Data: The mass flow rate of water, m=859 kg/s Mechanical power, 800 kW Electrical power, 779…

Q: What is mechanical efficiency? What does a mechanical efficiency of 100 percent mean for a hydraulic…

A: Mechanical efficiency: Mechanical efficiency is defined as the comparison of the energy at the inlet…

Q: Determine the overall efficiency of a pump which delivers 2.5 cubic meters per minute of water at…

Q: When water is pumped into a water tank 20 m above a lake with a flow rate of 70 l/s, 20.4kW of…

Q: The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 90…

A: Given that → Power inputW.=15 kW nmotor=0.9 V.=50LS=50x10-3…

Q: A 78-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.2…

A: The density of water is

Q: The three gorges dam is rated at maximum output. If its generating efficiency is 90 % and its head…

A: Given Data The efficiency of the dam is: η=90% The head of the dam is: h=51 m The capacity of the…

Q: The pump is used to increase the pressure of water from 100 kPa to 900 kPa at arate of 160 L/min. If…

Q: pump draws water at a head of 11Om and a discharge rate of 550 Ips. Determine the water power output…

A: Given Data H=110 m Q=550 LPs Pump efficiency=0.7

Q: The electric power needs of a community are to be met by windmills with 40-m-diameter rotors. The…

Q: A hydraulic turbine has 50 m of head available at a flow rate of 1.30 m3/s, and its overall…

A: Given: The available head of the turbine is H=50 m. The flow rate of the water in the turbine is…

Q: When water is pumped into a water tank 20 m above a lake with a flow rate of 70 l/s, 20.4kW of…

A: Given data:- Head(H) = 20 m Discharge(Q) = 70 L/sec Electric power = 20.4 k

Q: A river flowing steadily at a rate of 167 m3/s is considered for hydroelectric power generation.…

Q: Water enters a hydraulic turbine through a 35-cm-diameter pipe at a rate of 0.8 m3/s and exits…

A: Bernoulli's equation relates the pressure energy, kinetic energy and potential energy of a fluid…

Q: A pump is used to raise water to a reservoir through 800 m of 20 cm diameter pipe (f=0.033). If the…

Q: A cylindrical well is 2m in diameter and 12 m deep. If there is 3m of water in the bottom of the…

A: Given that: Diameter of the well = 2 m Depth of the well = 12 m Depth of water inside the well = 3 m…

Q: A water station must discharge 450 m3 / h to supply a city. Determine the plumbing so that the…

A: Let us design the plumbing i.e pipe size for given discharge and velocity of fluid. Given data, Q =…

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site H m below…

A: Mass flow rate of water, m˙=900 kg/s Mechanical power output of Turbine, PT=800 kW Electric power…

Q: In a Francis turbine, the pressure gage in the turbine casing reads 394 kpa. The elevation above…

Q: Well water is pumped into a tank that is 25 meters high through a pipe with an inner diameter of…

A: Given, head , h = 25 m inner diameter, d = 3.75 flow rate, q = 45 litres per min = 0.00075 m3/s…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

Q: A turbine is placed at the bottom of a 20-m-high water body. Water flows through the turbine at a…

A: Given: The height of the body is H=20 m. The rate of flow of the water is V=30 m3/s. The shaft power…

Q: Electric power is to be generated by installing a hydraulic turbine-generator at a site 120 m below…

A: Hydraulic Head of Turbine, H=120mWater flow rate, m˙=930 kg/sMechanical power output,PM=850…

Q: Choose correct answer: Pump converts ___________ A. Mechanical energy to Hydraulic energy B.…

A: Pump converts the Mechanical energy into hydraulic energy of the liquid.

Q: Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.6 m3/s and exits…

A: Given data: The diameter of the entrance of the pipe, D1 = 30 cm. Flow rate of water, V = 0.6 m3/s.…

Q: The pump is to increase the pressure of 0.3 m3/s of water from 100 kPa to 500 kPa. If the pump is…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: Define the overall efficiency of a turbine– generator is the product of the efficiency of the…

A: Turbine Efficiency is the ratio brake output to the internal output ηT=Brake Output of…

Q: A hydraulic turbine is used to generate power by using the water in a dam. The elevation difference…

A: Given data: Hydraulic turbine used to generate power in hydroelectric power station Net head (H)…

Q: A pump increases the pressure of water from 100 kPa to 1.2 MPa at a rate of 0.5 m3 /min. The inlet…

A: Given data: The pressure at the inlet of the pump, Pin = 100 kPa. The pressure at the outlet of the…

Q: Water is being pumped into a pool whose cross section is 10 ft x 13 ft while water is discharged…

Q: A pump shown in the Figure 3a below delivers water of density 1000 kg/m3 through a pipe of internal…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: In a hydroelectric power plant, water flows from an elevation of 400 ft to a turbine, where electric…

A: Given: Total head = 400 ft Head loss = 36 ft Net head = 400 - 36 = 364 ft =110.95 m

Q: In a large pumped hydro plant, the head from the turbine to the lake surface is 100m. During a…

A: Given : P = 50 MW η=0.7 h = 100 m t = 8 hrs = 28800 s To find : Amount of water pumped

Q: A river flowing steadily at a rate of 125 m3/s is considered for hydroelectric power generation. It…

A: Data given Q = V• = 125 m3/s h = 70 m

Q: Electric power is to be generated by installing a hydraulic turbine—generator at a site 120 m below…

A: Given Data Electric power generation is 770 kW. Mechanical power output of the turbine is 850 kW.…

Q: A hydro electric plant having 30 sq. km reservoir area and 100 m head is used to generate power. The…

Q: Neglecting air resistance, determine to what height a vertical jet of water could rise if projected…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A: Given Gross head, HG = 25 m Head loss, h = 5 m Net head, H = 25 - 5 = 20 m…

Q: A pump rated at 1800 W is used to transfer water from an open tank to another open tank. The…

A: To Find : The efficiency of the pump. Given : The power input to the pump Pin=1800 W. The height…

Q: A hydraulic turbine is used to generate power by using water in a dam. The elevation difference…

Q: The brake horsepower and water horsepower of a pump are determined to be 15 kW and 12 kW,…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

A 15-hp (shaft) pump is used to raise water to a 42-m higher elevation. If the mechanical efficiency of the pump is 82%, determine the maximum volume flow of water.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The elevation of the dam is about 110 m above the power plant, and the total irreversible head loss in the piping system is determined to be 25 m. If the electric power output estimated to be 60 MW, determine the efficiency of the turbine–generator.
What is mechanical efficiency? What does a mechanical efficiency of 100 percent mean for a hydraulic turbine?
A hydraulic turbine is used to generate power by using water in a dam. The elevation difference between the free surface stream and the downstream of the dam is 120 m. The water is supplied to the turbine at a rate of 150 kg/s. if the shaft power output from the turbine is 155 KW, the efficiency of the turbine is
A boat moved by jet propulsion discharges water through a jet of area 0.02 m2; the water being drawn from inlet opening facing the direction of motion. The total drag is estimated to be 17.66 u2 N·m where u is the speed of the boat in metre per second. Take density of water at 1,020 kg/m3 and efficiency of the pump set is 78%. If the boat moves at 54 kilometers per hour, determine the following: A) Relative velocity of the jet in meters per second B) The power, in kilowatts, of the motor required to work the pumps C) Efficiency of propulsion, in %
A water pump delivers 6 hp of shaft power when operating. If the pressure differential between the outlet and the inlet of the pump is measured to be 1.2 psi when the flow rate is 15 ft^3/s the changes in velocity and elevation are negligible, determine the mechanical efficiency of this pump. Show the energy diagram and label it accordingly
The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is 90 percent. The water flow rate through the pump is 50 L/s. The diameters of the inlet and outlet pipes are the same, and the elevation difference across the pump is negligible. If the pressures at the inlet and outlet of the pump are measured to be 100 kPa and 300 kPa (absolute), respectively, determine the mechanical efficiency of the pump.
For a pump, discuss the difference between brake horsepower and water horsepower, and also define pump efficiency in terms of these quantities.
Include a free body diagram. Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW (shaft) pump. If the irreversible head loss of the piping system is 5 m, determine the mechanical efficiency of the pump. prove the answer: 73.6 percent
Determine the discharge of a flowing fluid from a nozzle, whose specific gravity is 1.3, the nozzle is 15m above the datum. The power on the nozzle is 20KW and the velocity of flow is 10 m/s.
When water is pumped into a water tank 20 m above a lake with a flow rate of 70 l/s, 20.4kW of electrical power is consumed. Determine the efficiency of the pump-motor group by ignoring the friction losses in the pipes and the change in kinetic energy. Calculate the efficiency of the pump-motor group.
The three gorges dam is rated at maximum output. If its generating efficiency is 90 % and its head is S1 m what is the rate of flow in (kg/s) of water through its turbines at maximum output.
A hydraulic turbine generator was installed at a site 101 m below the free surface of a large water reservoir that can supply water steadily at a rate of 859 kg/s. If the mechanical power output of the turbine is 800 kW and the electric power generation is 779 kW, solve for the overall efficiency of this plant. Express your answer in decimal form with 3 decimal places.