A 4500/16000V, 1500 kVA, 50 Hz transformer has the following parameters: R1 = 0.03 2, R2 = 0.44 2, RO = 1688 Q xI - 0.092 2, X2 = 1.34 2, X0 = 256 2 The transformer is supplying full- load at power factor of 0.8 lagging. Using exact equivalent circuit, find the input current. [346.4 2- 38.94°A]

A 4500/16000V, 1500 kVA, 50 Hz transformer has the following parameters: R1 = 0.03 2, R2 = 0.44 2, RO = 1688 Q xI - 0.092 2, X2 = 1.34 2, X0 = 256 2 The transformer is supplying full- load at power factor of 0.8 lagging. Using exact equivalent circuit, find the input current. [346.4 2- 38.94°A]

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.15P: Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at...

See similar textbooks

Related questions

Q: A 4 MVA, 66/13.2 Kv, 50 Hz. Delta star connected Three phase transformer has a primary resistance…

A: The current flowing in a circuit causes a voltage drop. The voltage drop should be within allowable…

Q: 1. Design a 150VA power, 240V input, 48V and 12V single-phase transformer. G:25 mm, E: 12.5 mm, F:…

A: Given: The rating of a single-phase transformer is 150 VA, 240 V/48 V-12 V where G:25 mmE:12.5…

Q: 4.5 +J6 ohms referred to the high-Voltag A 1200/240-V practical transformer has an equivalent…

Q: Flag this question for future reference What is the test that can be conducted in the laboratory to…

A: In this question we have to determine in which test transformer impedance drops are dependent on…

Q: 23/A) A 1000-VA 230/115-V transformer has been tested to determine its equivalent reunt. The results…

Q: From the short circuit test and open circuit test in #19 and #20, the equivalent circuit of a…

Q: The table below shows some performance parameters of a certain power transformer. Full-load voltage…

Q: A short circuit test on a 15KVA,2400/240V, 50hz transformer yields the following results: 6.25A,131V…

A: In this question, We need to determine the voltage regulation If power factor is 0.8 lagging and…

Q: For the following ideal transformer circuit, the turns ratio N1:N2 is 6:1, Rsupply = 30 kΩ, and…

Q: The idle operating current of the three-phase transformer connected to Yy0 (Y-Y) with a power of…

A: Given transformer with rating 6300 KVA and 15/0.4 KV The no load current I0=2.91No load active power…

Q: 2- Calculate the values of Ro, X,, Reg1 and Xeg1 of the equivalent circuit of a 1-ph, 4KVA,…

Q: 1. )A single-phase transformer has a voltage ratio on open-circuit of 3300/660-V. The primary and…

A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…

Q: Problem 6.10: A 2-MVA, 4160/480 V transformer has series impedance of R= 2% and X = 6%. Determine…

A: The solution can be achieved as follows.

Q: A 60HZ transformer having a 480 turn primary winding takes 80 W in power and 1.4 A in current at an…

A: No load power factor=power at noloadvoltage×current. EMF =4.44 frequency ×flux×primary turns.

Q: With base MVA of 150 and base voltage of 33. If the reactance of the transformer is 0.23 pu. The…

A: Base MVA S= 150MVA Base voltage VB = 33kV Reactance per unit = 0.23 Reactance?

Q: transformer as shown in the figure given below. transformer is connected to form an auto A…

Q: An ideal transformer is connected to a voltage source given by es(t) = 100cos(2000nt)V on the…

A: In this question, Ideal transformer is connected to the es = 100cos(2000πt) V. Transformer turn…

Q: In no-load mode a single phase two windings power transformer draws apparent power S10=100VA at…

Q: A 3 kava, 500/250 V, 50 Hz, step-down transformer has the following parameters: Re1 = 3.5 ohm, Xe1 =…

A: A 3 KVA, 500/250 V, 50 Hz, step-down transformer parameters: Re1 = 3.5 ohm, Xe1 = 4.5 ohm, Rc1 =…

Q: a step-down transformer of 23 kVA, 2300 V / 230 V, 50 Hz, R1 = 4 Ω, X1 = 12 Ω, R2 = 0.04 Ω, X2 =…

A: a) Calculate the rated current by substituting the values of V=230 V, P=23 kVA in the power…

Q: A 23-kVA, 2300/230-V, 60-Hz, step down transformer has the following resistance and leakage-…

Q: SKVA, 50Hz, single phase transformer, the primary voltage of the transformer is 110V. Reqand X is…

A: Given data, Voltage (Vp)=220 VResistance(Req)=026ΩImpedance(Xeq)=0.4ΩVoltage…

Q: 1. An ideal transformer with N, 2400 and N2 = 400 is connected with an imped %3D across winding 2,…

Q: Q1) The equivalent low-side parameters of a 250kVA, 4160 - 480V, 60 = = 0.0433 9. The Hz transformer…

A: Given,For a low-side transformer,S=250kVAVload=4160 VV=480Vf=60HzReq,LS=0.00920 ΩXeq, LS=0.0433…

Q: Open-circuit, and short-circuit tests were conducted on a 50 kVA, 6 360/240 V, 50 Hz, single- phase…

Q: A 5 KVA 220/110 transformer has the following parameters. Ri -0.25Ω , Χ -0.75Ω, Reι -720 Ω , Xm1-180…

A: According to question, Given transformer of 5KVA 220/110 transformer has R1=0.25 ohm, X1= 0.75 ohm,…

Q: 1- A single phase transformer with a ratio of 6600/400 V takes to no-load current of 0-7 A at 0-24…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: 7. The primary of a single-phase transformer takes 1 A at power factor of 0.4 when connected to a…

A: In the question, Primary current Ip = 1A at 0.4PF logging with secondary side open. Secondary side…

Q: Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The…

Q: A 1000-VA, 230/115-V traformer has been tested to determine its equivalent circuit. The results are…

Q: A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1…

Q: For any transformer, one can prove that Il*N1/fl=12*N2*f2, where fl and f2 denote the frequencies of…

A: Transformer is an static device which convert energy from one circuit to other circuit using primary…

Q: An (15-0.X) kVA, 110/440, 60 Hz, two winding transformer has low voltage side resistance of…

Q: Question 1 1. Discuss the working principle of a linear variable differential transformer. 2. An…

A: Question 1 : 1) Linear variable differential transformer : LVDT is an electromechanical device…

Q: A step-down transformer is rated 10kVA, 7500/250 V and has the following equivalent circuit…

A: In this question, We need to determine the equivalent winding impedance referred to the high…

Q: Q.2: The parameters of a 200/3000V, 50Hz single phase transformer are given below: R₁-0.018 02,…

A: It is given that: R1=0.018 ΩX1=0.004 ΩR2=0.018 ΩX2=10 ΩRo=150 ΩXo=800 ΩZL=50-j75 Ω

Q: A 15-kVA, 2400/240-V transformer is to be tested to determine its excitation branch components, its…

A: Solutiongiven that ,Rated KVA=15KVAVoltage rating =2400/240VOpen circuit…

Q: 1. A 10 kVA, single-phase, 2400-V:120-V, 60 Hz transformer has an equivalent impedance referred to…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

Q: Parameters of a distribution transformer of 20 kVA, 2200/220 V, 50 Hz, R1 -5Ω R2-0.04 Ω Rc-3000 Ω…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined.…

A: In this question, We need to impedance of the approximately in the primary side and draw the…

Q: The single-phase equivalent circuit parameters appearing on the high voltage (primary) windings side…

A: Given,primary winding internal resistance, R1=0.65Ωprimary winding leakage reactance,…

Q: A 19kVA transformer steps down from 3300V to 240V. The resistance of the primary and the secondary…

Q: 6. A 300 kVA, single-phase transformer is designed to have a resistance of 1-5 % and maximum…

A: In this question we need to find a efficiency of transformer at given loading conditions.

Q: A 7200-240-V, 60-Hz transformer is connected for step-up operation, and a 144/46°-2 load is…

A: Given data, The value of turn ratio is n2n1=7200240. The value of load resistance is R = 144∠46∘ Ω…

Q: Primary side-reduced equivalent circuit parameters of a 25 KVA, 50 Hz, 4000/400 Volt transformer R1…

A: Given: A 25KVA, 50Hz, 4000/400V transformer in which…

Q: 6- A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full- load and half-load at unity…

A: In this question we need to find efficiency of transformer for given loading conditions.

Q: 9. A 10-kVA, 2000/400-V, single-phase transformer has resistances and leakage reactances as follows:…

A: Given, Primary voltage, V1 = 2000 V Secondary voltage, V2 = 400 V So, transformation ratio,…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

A 4500/16000V, 1500 kVA, 50 Hz transformer has the following parameters: R1 = 0.03 2, R2 =
0.44 2, RO = 1688 Q xI - 0.092 2, X2 = 1.34 2, X0 = 256 2 The transformer is supplying full-
load at power factor of 0.8 lagging. Using exact equivalent circuit, find the input current. [346.4 2-
38.94°A]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase, 50-kVA,2400/240-V,60-Hz distribution transformer has the following parameters: Resistance of the 2400-V winding: R1=0.75 Resistance of the 240-V winding: R2=0.0075 Leakage reactance of the 2400-V winding: X1=1.0 Leakage reactance of the 240-V winding: X2=0.01 Exciting admittance on the 240-V side =0.003j0.02S (a) Draw the equivalent circuit referred to the high-voltage side of the transformer. (b) Draw the equivalent circuit referred to the low-voltage side of the transformer. Show the numerical values of impedances on the equivalent circuits.
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
For the transformer in Problem 3.10. The open-circuit test with 11.5 kV applied results in a power input of 65 kW and a current of 30 A. Compute the values for GcandBm in siemens referred to the high-voltage winding. Compute the efficiency of the transformer for a load of 10 MW at 0.8 p.f. lagging at rated voltage.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
The transformer of Problem 3.16 is supplying a rated load of 50 kVA at a rated secondary voltage of 240 V and at 0.8 posr factor lagging. Neglect the transformer exciting current. (a) Determine the input terminal voltage of the transformer on the high-voltage side. (b) Sketch the corresponding phasor diagram. (c) If the transformer is used as a step-down transformer at the load end of a feeder whose impedance is 0.5+j2.0, find the voltage VS and the power factor at the sending end of the feeder.
An ideal transformer has no real or reactive power loss. (a) True (b) False