A 7.5 cm radius vertical cylinder rotates concentrically inside another cylinder of radius 7.55 cm. Both cylinders are 25 cm high. The space between the cylinders is filled with liquid whose viscosity is unknown. If a torque of 12.0 N is required to rotate the inner cylinder at 110 rpm, determine the viscosity of the fluid.

A 7.5 cm radius vertical cylinder rotates concentrically inside another cylinder of radius 7.55 cm. Both cylinders are 25 cm high. The space between the cylinders is filled with liquid whose viscosity is unknown. If a torque of 12.0 N is required to rotate the inner cylinder at 110 rpm, determine the viscosity of the fluid.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A thin plate travels between two plane, parallel, horizontal and stationary surfaces at a constant speed of 7 m/s. The two stationary surfaces are spaced 6 cm apart, and the middle is filled with oil of viscosity of 0.9 Ns/m2.The moving plate submerged in oil has a length of 2 m and a width of 0.5 m. (i) If the plate moves through the mid-plane between the surfaces, determine the force required to maintain this motion. (ii) Determine the force if the plate was 1 cm from the bottom surface and 2 cm from the top surface?
A cylinder of 125mm radius rotates concentrically inside a fixed cylinder of 130mm radius. Both cylinders are 300mm long. Determine the viscosity (in Pa-s) of the liquid which fills the space between the cylinders if a torque of 0.88 N-m is required to maintain an angular velocity of 2n radians/sec.
The figure below represents a cylinder C i (d = 11 cm) that is inside a hollow cylinder (d = 11.1 cm). The inner cylinder, with a mass of 30 kg and a length of 25 cm (L), is subjected to a pressure P of 50 kPa at its bottom, rising at a constant speed of 2.5 m/s. a) Determine the dynamic viscosity of the lubricating oil that must be placed in the space between the piston and the cylinder; b) Determine the kinematic viscosity knowing that it consists of a mixture of 3 L of oil A (specific mass of 880 kg/m 3 ) and 2200 mL of oil B (specific mass of 940 kg/m 3 ). Data: g = 9.81 m/s 2
What is the difference between dynamin and kinematic viscosity? That is the significance of these properties of liquid?
Two concentric cylinders are rotating in opposite directions but the same speed, 25 revolutions per minute. The outer cylinder, 11cm in diameter, is turning counterclockwise and the inner cylinder, 10 cm in diameter, is turning clockwise. The gap between the cylinders is filled with a liquid. The liquid is a Newtonian fluid with a viscosity of 0.1 kg/m.s. Both cylinders are 50 cm long. Assuming linear distribution of velocity in the gap, Sketch the velocity profile inside the liquid in the gap At what radial distance from the center of the cylinders the liquid velocity becomes zero? Find the shear rate Find force acting on each cylinder
An oil is contained between 2 identical parallel plates of 2m2area each. The top plate is pulled tothe left (-x direction) with a force of 0.33N at a velocity of 0.3 m/s. The bottom plate is pulled in theopposite direction with a force of 0.11N at a velocity of 0.1 m/s. The plates are 5mm apart. Whatis the viscosity of the oil in cP?
Determine the total force required to drag a thin plate which is placed in between two parallel plates 2.6 cm apart with the space filled with a fluid of viscosity of 0.55 Ns/m2.The area of the plate is 0.475 m2 and the speed at which it is dragged is 0.4 m/s. The position of thin plate from the top plate is 0.2 cm?
The space between two parallel plates 0.001 ft apart is filled with oil viscosity 0.7cp. The top plate is stationary while the lower plate is moving in the x-direction with a velocity 1ft/sec. A. Determine shear rate B. What should be the shear stress in lbf/ft^2? Answer asap pls
The viscosity of a fluid is to be measured by a viscometer constructed of two 40-cm-long concentric cylinders . The outer diameter of the inner cylinder is 12 cm, and the gap between the two cylinders is 0.15 cm. The inner cylinder is rotated at 300 rpm, and the torque is measured to be 1.8 N⋅m. Determine the viscosity of the fluid.
A piston with a diameter of 6 cm and a length of L = 13 cm rotates at n = 105 rpm in a cylinder of 6.04 cm in diameter as shown in the figure. Since the dynamic viscosity of the oil between the piston and the cylinder is 1.075 kg · sec · m-2, calculate the moment value that should be applied to the piston rod. M=?
A viscometer constructed of two 30-cm-long concentric cylinders is used to measure the viscosity of a fluid. The outer diameter of the inner cylinder is 9 cm, and the gap between the two cylinders is 0.18 cm. The inner cylinder is rotated at 250 rpm, and the torque is measured to be 1.4 N⋅m. The viscosity of the fluid is (a) 0.0084 N⋅s/m2 (b) 0.017 N⋅s/m2 (c) 0.062 N⋅s/m2 (d ) 0.0049 N⋅s/m2 (e) 0.56 N⋅s/m2
In the study of fluid phenomena, how does Newton's Law of Viscosity affect your calculations?