Calculate the ammeter reading in the electrical circuit?

Q: 1. F. -- plan of room or floor of building drawn to scale. - shows the meaning of every symbol…

A: As per the guidelines, we supposed to answer the first three-part of the question at a time so…

Q: Give me about ten examples of electrical code violations in maintenance and repair. Hopefully the…

A: Choose the wrong Circuit breaker There is a need to follow the national electric code. 1. Standard…

Q: The _______ point is where the facilities of the serving utility and the premises wiring connect. A.…

A:

Q: Explain how to do a continuity check on an electrical appliance plug. Explain how to test for…

A: Continuity test is performed to analyze where the flow of the electric current is continuous on not,…

Q: What it the accuracy of the meter when measuring resistance?

A: we need to explain given statement.

Q: what is  the largest size overcurrent protection device (fuse or breaker) allowed to protect the…

A: Concept: The circuit which is used to electrically describe and model either continuous materials or…

Q: A 600 volt, 100 amp class K fuse will fit into the same fuse holder as a 600 volt ,100 amp RK fuse.…

A: Class K fuse-   This is the fuse available in the DC Rating.   Current and voltage ratings are…

Q: What color is used for the identification of wiring device terminals?     A. green…

A: The equipment grounding conductor of green color is used to identify the wiring device terminals.

Q: What should a multimeter NOT DO when testing sophisticated equipment such as medical equipment?

A:

Q: Skitch  a wire of installation

A: Sketch  a wire of installation

Q: Technician A says electronic transmission controls can malfunction if not provided with a good…

A: The electronic controls are governed by a good voltage source which plays an important role in…

Q: A cable has a VSWR of 10. If the minimum voltage along the cable is 20 volts, what is the maximum…

A:

Q: You are an electrician working in an industrial plant. The company is constructing a maintenance…

A:

Q: Draw wiring layout for controlling Lamp A and Lamp B by Switch B and Switch A

A: The most common use of a two-way switch is Staircase wiring where a light can be controlled by two…

Q: what switch type and rating is required to control five 300 watt tugsten filament lamps on a 120…

A:

Q: Draw wiring layout for controlling Lamp A and Lamp B by Switch AB .

A: This type of layout is used in top and bottom of a staircase at homes , corridors or wherever…

Q: Using the image above, what type of contact is used to turn on the "LIGHTS"?

A: here as shown in the ladder diagram two switch S1 and S2 are used to turn off or on the Lights.

Q: What is the most common voltage usted for control system

A: There are two basic components which are used in the most common voltage for the control system; 1.…

Q: Installations used to export electric power from vehicles to premises wiring or for?current flow are…

A:

Q: If you were to place your meter in parallel with a set of closed switch contact that had 120 volts…

A: Assuming there is no resistance in the path, the situation has been shown in the circuit diagram…

Q: What is indicating when I'm reading a 26 ohms on my meter?

A: Reading 26 ohms on meter

Q: How is an ammeter connected into a circuit

A: An ammeter is an apparatus which is used to compute current in the circuit. An ammeter has a fixed…

Q: Explain the method of carrying out insulation resistance test on an electrical installation

A: Insulation resistance is the quality of an electrical system that degrades with time, temperature,…

Q: When seeking to measure the voltage of a wall outlet (120 Volts AC) an electrician needs to do the…

A: Simpson 260 is an analog volt ohm milliammeter  that can used to measure voltage current and…

Q: 5. What wattage for the clothes closet luminaires was used for calculating their contribu- tion to…

A: The wattage of closet luminous for,

Q: How many spaces does a 3-pole circuit breaker take up in an electrical panel?

A: Three pole circuit breaker is mostly used in commercial facilities, workshops and factories where…

Q: Draw the primary protection zones for each element of the system in the figure shown.

A: We have to draw the primary protection zones for the given power system shown below:

Q: What code sets stabdard for the electrical installation work?

A: In the following section, the code which sets standards for electrical installation work has been…

Q: If you know that the power of the load that is supplied with a voltage source of (220 volts) is 2000…

A: The resistance of the wire can be written as                           R=ρlAA=ρlR For voltage V and…

Q: 20.a. What's the maximum number of switches or circuit breakers the service-disconnecting means may…

A:

Q: What is the major cause of creeping in an energy-meter?

A: According to the question we have to discuss major cause of creeping in an energy-meter?

Q: For track lighting in a church, a load of not less than ______ shall be included in every ____ foot…

A: As per general standard, for a regular interval of 2ft a load with a minimum rating of 150VA must be…

Q: Fuses are intended to protect the house wiring, not people.

A:

Q: an electrical system operates at a potential higher than 600 volts, the nonmetallic conduit must be…

A: The correct option is 2inches.

Q: What are different types of the power associated in the electrical circuit?

A: In the electrical circuit, there are three kinds of power associated with the circuit that is real…

Q: difference betwwen fuse and circuit breaker ?

A: Fuse : A fuse can be defined as an electrical safety device which protects an electrical circuit…

Q: Appliances consuming high amount of power and powered by mechanical energy like Air con must be…

A: People are protected by ground fault circuit interrupters (GFCIs) in situations where they are prone…

Q: Determine the power provided by the 20-volt source in the circuit below. Indicate if the 20-volt…

A: The given circuit is:

Q: Determine the proper size of copper wire conductor necessary to apply a 750 W electric motor that is…

A: It is given that: P=750 WL=100 feetVpanel=120 voltsVdrop=1.2 volts

Q: Fuse and circuit breakers are the common household circuit.   TRUE OR FALSE

A: Answer: TRUE  Because Nowadays  in every where we use these fuses and circuit breaker to protect our…

Q: Explain why test lights are not recomended for testing computer circuits

A: Test lights are not recommended for testing computer circuits because they are used where circuits…

Q: Please draw the block diagram of Standby UPS.

A: UPS stands for uninterruptible power supply.  It is used as instant power backup if supply is…

Q: Under what conditions did the power supply register current?

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.