(a)A garden hose attached with a nozzle is used to fill a 20-gallon bucket. The innerdiameter of the hose is 2 cm, and it reduces to 0.8 cm at the nozzle exit. If it takes 55 s to fillthe bucket with water, determine the volume and mass flow rates of water through the hose,and the average velocity of water at the nozzle exit. Comment on the result.

Answered: Image /qna-images/answer/8c9d6cf7-3df4-4ad9-95c2-69abd36a2bad.jpg

Answered: (a) A garden hose attached with a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A garden hose attached with a nozzle is used to fill a 40-literbucket. The inner diameter of the hose is 2.0 cm, and it reduces to1.0 cm at the nozzle exit. If it takes 59N s to fill the bucket withwater, determine (a) the volume and mass flow rate of waterthrough the hose, and (b) the mean velocity of water at the nozzleentry and exit
A garden hose attached with a nozzle is used to fill a 40-liter bucket. The innerdiameter of the hose is 2cm, and it reduces to 0.8cm at the nozzle exit. If it takes 50 secondsto fill the bucket with water, determine:(a) the volume and mass flow rates of water through the hose, and(b) the average velocity of water at the nozzle exit.
A garden hose attached with a nozzle is used to fill a 22-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.5 in at the nozzle exit. If the average velocity in the hose is 7 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.
A desktop computer is to be cooled by a fan whose flow rate is 0.40 m3/min. Determine the mass flow rate of air through the fan at an elevation of 3400 m where the air density is 0.7kg/m3. Also, if the average velocity of air is not to exceed 110 m/min, determine the minimum diameter of the casing of the fan.
Oxygen enters a nozzle steadily at 2 kg/m3 and 35 m/s and leaves at 0.76 kg/m3 and 180 m/s. If the inlet area of the nozzle is 85 cm2, what is the exit area of the nozzle in cm2.
The shaft power of a turbine operating with 80 percent efficiency is 450 kW. If the mass flow rate through the turbine is 625 kg/s, the load removed from the fluid by the turbine iswhat is the amount? Take it as g=9.81 m/s2
(Open System) A garden hose attached with a nozzle is used to fill a 10 gal bucket. The inner diameter of the hose is 2cm and it reduces to 0.8 cm at the nozzle exit. If it takes 50s to fill the bucket with water, determine a) volumetric flowrate( L/s) and mass flowrate (kg/s) of the water through the hose b) average velocity of water at the nozzle exit (m/s)
A wind tunnel draws atmospheric air at 20° C and 101.3 kPa by a large fan located near the exit of the tunnel. If the air velocity in the tunnel is 80 m/s, determine the pressure in the tunnel.
Air flows in a steady manner through a converging tube. At the inlet there are 690kPaa and 1.193m3/kg. If 125m3/min of air enters at the rate of 1.57 m/sec and the exit section has a diameter of 35cm, determine (a) the mass flow rate in kg/sec, (b) the diameter of the entrance section in mm and (c) the exit velocity in m/min.
Air enters a nozzle steadily at 2.21 kg/m3 and 20 m/s and leaves at 0.762 kg/m3 and 150 m/s. If the inlet area of the nozzle is 60 cm2, determine (a) the mass flow rate through the nozzle, and (b) the exit area of the nozzle.
Air whose density is 0.078 lb/ft^3 enters the duct of an air-conditioning system at a volume flow rate of 450 CFM. If the diameter of the duct is 10 in, determine the velocity of the air in fpm at the duct inlet.
Refrigerant R-134a enters a 30cm diameter pipe (circular cross-section) at an absolute pressure of 200 kPa and a temperature of 10 °C with a velocity of 5 m/sec. Heat is transferred to the refrigerant as it flows and the gas leaves the pipe at 180 kPa and 50 °C. Find the following quantities:a. The density of the gas at the inlet and exit of the pipe.b. The mass flow rate of the refrigerant in kg/sec.c. The volume flow rate at the inlet in m3/sec.d. The volume flow rate at the exit in m3/sec.e. The exit velocity in m/sec.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS