I need only handwritten or i will dislike for sure A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the datatable, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x = 44 mm.given in theAluminumBrassModulus of elasticity70 GPa105 GPaAllowable stress100 MPa160 MPa10 mm10 mmAluminum10 mmBrass40 mm10 mm2.46 kN-m.The largest permissible bending moment when the composite bar is bent about a horizontal axis is

Disclaimer As you have mentioned that you need answer in hand written but the portal we are using…

A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x = 44 mm. Aluminum Brass Modulus of elasticity 70 GPa 105 GPa Allowable stress 100 MPa 160 MPa 10 mm 10 mm Aluminum 10 mm Brass 40 mm 10 mm

A bar having the cross section shown has been formed by securely bonding brass and aluminum stock. Using the data given in the table, determine the largest permissible bending moment when the composite bar is bent about a horizontal axis. Take x = 44 mm. Aluminum Brass Modulus of elasticity 70 GPa 105 GPa Allowable stress 100 MPa 160 MPa 10 mm 10 mm Aluminum 10 mm Brass 40 mm 10 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 69∘F. Compute the stress (ksi) in the Aluminum at 118 ∘F. Assume α= 6.5 x 10-6/∘ F for steel and 12.8 x 10-6/∘F for aluminum Given: L1 = 17in; L2 = 11in Your final answer should contain two decimal places
Compute the value the shear modulus G of steel whose modulus of elasticity E is 200 GPa and poisson's ratio is 0.30.
A steel bar of rectangular cross section 45 mm (height) x 60mm (base) and pinned at each end is subject to axial compression. The proportional limit of the material is 320 Mpa and E= 200 GPa. -Find least Radius of Gyration (in mm)? -Determine the transition length (in mm) in which the Parabolic formula may be used instead of the Euler's equation.? -Determine the transition slenderness ratio in which the Parabolic formula may be used instead of the Euler's equation.? -If the Length is 1 meter, determine the critical load (in KN) using pin support. -if the length is 3 meters, determine the critical stressn(in MPa) using pin support.
The composite beam shown in the figure is simply supported and carries a total uniform load of 40 kN/m on a span length of 4.0 m. The beam is built of a southern pine wood member having cross-sectional dimensions 150 mm 250 mm and two brass plates of cross-sectional dimensions 30 mm 150 mm. (a) Determine the maximum stresses B and w in the brass and wood, respectively, if the moduli of elasticity are EB 96 GPa and Ew 14 GPa. (Disregard the weight of the beam.) (b) Find the required thickness of the brass plates so that the plate and wood reach their allowable stress values, saB 70 MPa and saw 8.5 MPa, simultaneously under the maximum moment. What is the maximum moment?
The compound bar ABCD has a uniform cross-sectional area of 0.25 in.² When the axial force P is applied, the length of the bar is reduced by 0.018 in. Determine the magnitude of the force P. The moduli of elasticity are 29 x 10^6 psi for steel and 10 x 10^6 psi for aluminum. Please include the details. Thank you.
Compression Steel Given: The beam cross-section shown have the following cross-sectional properities: f'c = 4000 psi Find phi Mn.
The composite shaft shown in the figure is manufactured by shrink-fitting a steel sleeve over a brass core so that the two parts act as a single solidbar in torsion. The outer diameters of the two parts are d1 = 1.6 in. for the brass core and d2 = 2.0 in. for the steel sleeve. The shear moduli of elasticity are Gb = 5400 ksi for the brass and Gs = 12,000 ksi for the steel.(a) Assuming that the allowable shear stresses in the brass and steel are τb = 4500 psi and τs = 7500 psi, respectively, determine the maximumpermissible torque Tmax that may be applied to the shaft.(b) If the applied torque T =15 kip-in., find the required diameter d2 so that allowable shear stress τs is reached in the steel.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The assembly shown is made up of T-shape steel and two wood as shown. A bending moment M is applied to the composite beam. Given: Es = 200 GPa Ew = 25 GPa M = 90 kN.M h = 200 mm c. Calculate the absolute maximum stress in the steel in MPa. d. Calculate the stress in the steel along the top edge in MPa.
A .What is the value for HB? * b. What is the value for x? c. What is the value for y? * d. What is the potential value for Modulus of Elasticity in steel? e. What is the resultant force member IG? *
A 5 ft. long laminated wood beam is built up by gluing together three 2” x 6” boards to form asolid beam 6” x 6” cross section, as shown in the figure. Calculate the maximum allowable valueof P (lb.) such that both the (1) allowable shear stress in the glued joints of 100 psi and the (2)allowable bending stress of 1200 psi is not exceeded. (Disregard the weight of the beam).[Formula: Bending Stress:  = (M)(y)/I; max = (M)(c)/I; Transverse Shear Stress:  =(V)(Q)/(I*t); max = (V)(QNA)/(I*tNA)]
The strain in member AB was measured to be 9 × 10^−4. If the member is an ? 3 × 3 × 1/4 of A36 steel (refer to AISC Table 1-7, next page), determine thefollowing:a. What is the change in length in inches?b. What is the force in the member?Note: For all structural steels: modulus of elasticity, ? = 29,000 ksi
QU A composite beam is fabricated by bonding a steel bar and a brass bar and is subjected to the bending moment M = 200 N-m. Determine the maximum bending stress in the brass and steel. Given: E, =200 GPa, E, = 100 GPa Brass 20 }o | Jakrtal