A capacitor is fully charged in a RC circuit with 16 V of voltage supply to the maximum electric charge of 1.2 x 10-3 C. If it took 0.24 s to charge to 2/3 of charge, what will be the maximum current, in the unit of A, when discharging the capacitor? Assume that the same resistor is used for charging and discharging

A capacitor is fully charged in a RC circuit with 16 V of voltage supply to the maximum electric charge of 1.2 x 10-3 C. If it took 0.24 s to charge to 2/3 of charge, what will be the maximum current, in the unit of A, when discharging the capacitor? Assume that the same resistor is used for charging and discharging

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 1RQ: An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
You are a journeyman electrician working in an industrial plant. Your task is to connect an inductor to a 480-V, 60-Hz line. To determine the proper conductor and fuse size for this installation, you need to know the amount of current the inductor will draw from the line. The nameplate on the inductor indicates that it has an inductance of 0.1 H. An ohmmeter reveals that it has a wire resistance of 10 . How much current should this inductor draw when connected to the line?
Two capacitors having values of 80 F and 60 F are connected in series. What is the total capacitance?
Capacitance’s of 15μF, 12μF, 17μF, and 19μF are connected in parallel to a Direct Voltage Supply of 400V. Determine the: (A) Equivalent Circuit Capacitance, (B) Total Charge, and (C) Charge on each Capacitor.
A 20-uF capacitor has a voltage of 5V across it at t=0. If a constant current of 30mA flows through the capacitor, how long will it take for the capacitor to charge up to 180 uC?
A capacitor is connected to a 150-V supply. If the capacitor is being charged to 0.99 W-s. What is the capacitance of the capacitor?
Capacitors are used in circuits that emit radio frequencies used for remote controllers. You work at a remote controller store and you are given the following table of dielectric constants. If your task is to create a capacitor with the highest capacitance, what dielectric material would you choose and why? If you know the area of your parallel plate capacitor is 1m^2 and has a gap between plates of 1x10^-3m, what would be the difference in capacitance from the parallel plate capacitor in vacuum vs using the dielectric you choose?
Capacitors are fundamental electrical components that store energy in the form of an electric field. They consist of two conductors separated by an insulator, known as a dielectric. When a voltage is applied to the capacitor terminals, it accumulates opposite charges on the conductors, creating an electric field between them. What is the total capacitance (C) in farads (F) between terminals A and B in the capacitor arrangement present in the circuit below?
A 100-uF capacitor is charged by a constant current of 1mA. Find the voltage across the capacitor at t = 4s. Assume V(0) = 0 V.
Determine the time it takes for the capacitor shown in the following circuit to charge to half its maximum capacity