A circular cross-sectional rod made of AISI Type 303 Stainless Steel is normally operated at 126oF. Length and radius of the rod are 1.5 ft and 1.75 in., respectively. What would be the change in length of the rod, if it is subjected to a temperature of 214oF? Coefficient of thermal expansion of the rods’ material is 9.6 × 10^-6 in./in. Degrees Fahrenheit.

A circular cross-sectional rod made of AISI Type 303 Stainless Steel is normally operated at 126oF. Length and radius of the rod are 1.5 ft and 1.75 in., respectively. What would be the change in length of the rod, if it is subjected to a temperature of 214oF? Coefficient of thermal expansion of the rods’ material is 9.6 × 10^-6 in./in. Degrees Fahrenheit.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.1P: The rails of a railroad track are welded together at their ends (to form continuous rails and thus...

See similar textbooks

Similar questions

1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A square steel alloy plate 400 mm on a side has a 90-mm-diameter circular hole at its center. The plate is heated from 20°C to 45°C. The final diameter of the hole is ____ mm standard coefficient of thermal expansion: steel - 11.25x10^-6 / degrees celcius Aluminum - 23x10^-6 / degrees celcius
Coefficient of Thermal Expansion Steel Rod (figure) a. Change in length if the rod is heated to 200°C.b. Change in diameter if Tf = 200°C.c. Thermal stress if the ends are rigidly supported (initially stress-free) and the rod is heated by 180°C.d. Determine the thermal expansion of the following materials:- Rubber- Silver- Copper- Aluminum- Steel
1.A composite component is comprised of a tube and a concentric rod running inside it, both with a length of 1.5 meters. The tube is made of copper and has inner and outer diameters of 60 mm and 100 mm, respectively, a coefficient of thermal expansion and elastic modulus of 17 ×10−6? and 117 GPa, respectively. The rod is made of aluminium with a diameter, coefficient of thermal expansion and elastic modulus of 50 mm, 23 ×10−6? and 80 GPa, respectively. If the composite is exposed to a temperature rise of 120°C, determine:1.1 The sense and magnitude of the stresses induced in the composite if it is not restrained. 1.2 The sense and magnitude of the stresses induced in the composite if it is partially restrainedwith an allowed free expansion of 0.3 mm.
Bar A has a cross-sectional area of 0.04 m2, modulus of elasticity E = 70 GPa, and coefficient of thermal expansion α = 14E‐6 C-1. Bar B has a cross sectional area of 0.01 m2, modulus of elasticity E = 120 GPa, and coefficient of thermal expansion α = 16E‐6 C-1. There is a gap b = 0.4 mm between the ends of the bars. What minimum increase in the temperature of the bars above their initial temperature T is necessary to cause them to come into contact?
A copper tube having a cross-sectional area of 2000 mm2 and a length of 300 mm is placed between two rigid caps. Four 22 mm diameter steel bolts are symmetrically arranged parallel to the axis of the tube and are lightly fastened. Calculate: 2.1 The stress in the tube if the temperature of the assembly is raised by 70 oC. (15) 2.2 The load that each bolt will carry at the raised temperature (Est = 200 GPa; Ecu = 100 GPa; αst = 12 × 10-6/oC).
question 2 temperature stresses A composite bar is comprised of a concentric circular rod of copper and a tube of aluminium, each of length 500 mm, that are attached rigidly to above one another at both ends. The diameter of the copper rod is 30 mm, while the inner and outer diameters of the aluminium rod are 50 and 60 mm, respectively. The Young’s modulus and coefficients of thermal expansion for copper and aluminium are given as, 120 GPa and 80 GPa, and17 × 10−6 oC and 23 × 10−6/ o?, respectively Please show all formulas and substitutions into formulas 1 Calculate the magnitude of the stresses that are induced in the copper bar and aluminium rod if the composite bar is exposed to a temperature change of 500 oC, and state their senses. 2 Calculate the elongations of the constituents of the composite bar.
A mechanic needs to remove a tight fitting pin of material A from a hole in a block made of material B. The machinist heats both the pin and the block to the same high temperature and removes the pin easily. What statement relates the coefficient of thermal expansion of material A to that of material B?
A steel rod, 16 mm in diameter and 5 m length, is connected to two grips at each end at a temperature of 150 °C. Find the pull exerted when the temperature falls to 40 °C, if the ends (i) do not yield and (ii) yield by 1 mm. Take coefficient of thermal expansion = per °C and N/mm 2
A copper tube having a cross-sectional area of 2 000 mm2 and a length of 300mm is placed between two rigid caps. Four 22-mm-diameter steel bolts aresymmetrically arranged parallel to the axis of the tube and are lightly fastened.Find the stress in the tube if the temperature of the assembly is raisedby 70 °C. What load will each bolt carry at the raised temperature? (Let EST =200 GPa; Ecu = 100 GPa; aST = 12 x 10"6/oC; ac u = 16 x 10-6/°C.)
A load is supported by four 304 stainless steel wires that are connected to the rigid member’s AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 0.025 in2. When a 500 lb load is applied, the angle of telt is 0.0296° and 0.003405° for the AB and DC members respectively. If the load is reduced to 450 lb but the angles of telt are maintain, what is the temperature change?