A conical tube of length 2m is fixed vertically with smaller end upward. Velocity of flow at smaller end is 5m/s while at larger end is 2 m/s. The pressure head at the smaller end is 2.5 m of flowing liquid. Loss of head in the tube is given by 0.35-(vf-vý) where vi is velocity at smaller end while v2 is velocity at larger end. Solve for the 2g pressure head at the other end if the flow takes place a) downward, b) upward direction

A conical tube of length 2m is fixed vertically with smaller end upward. Velocity of flow at smaller end is 5m/s while at larger end is 2 m/s. The pressure head at the smaller end is 2.5 m of flowing liquid. Loss of head in the tube is given by 0.35-(vf-vý) where vi is velocity at smaller end while v2 is velocity at larger end. Solve for the 2g pressure head at the other end if the flow takes place a) downward, b) upward direction

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
What is the entrance length in a 4-cm-diameter pipe if 0.5*10^ -4 m^ 3 / s water is flowing
Determine the surface tension in a tube with 0.3m radius and wetting angle 80 and capillary rise of 4.5mm in N/m and in lb/ft.
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?
A hydraulic reaction turbine working under a head of 16 m develops 640 kW of power. What is the unit power of the turbine?
In a commercial steel pipe of diameter 0.01906 (in meters), industrial waste water (approximate as water at 30 °C) flows through it with an average velocity of 30 m/s. Determine the pressure drop using Moody chart. Determine the pressure drop using Colebrook Formula or Haaland Equation.
For the piping system of Fig. , all pipes are concretewith a roughness of 0.04 in. Neglecting minor losses, computethe overall pressure drop p1 - p2 in lbf/in2 ifQ =20 ft3/s. The fluid is water at 20°C.
An orifice of diameter 200 mm is fitted at the bottom of a boiler drum of length 6 m and diameter of 2 m. The drum is horizontal and half full of water. Find the time required to empty the boiler, given the value of Cd = 0.6
For the parallel-pipe system of Fig. each pipe iscast iron, and the pressure drop p1 - p2 = 3 lbf/in2. Computethe total flow rate between 1 and 2 if the fluid is SAE10 oil at 20°C.