A D0 = 10-m-diameter tank is initially filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 100-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V = √ _________ 2gz _________ 1.5 + f L/D where z is the water height above the center of the valve. Determine the initial discharge velocity from the tank.

A D0 = 10-m-diameter tank is initially filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 100-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V = √ _ 2gz _ 1.5 + f L/D where z is the water height above the center of the valve. Determine the initial discharge velocity from the tank.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter44: Geothermal Heat Pumps

Section: Chapter Questions

Problem 1RQ: Geothermal heat pumps, or water-source heat pumps, are classified as either _____loop or _____loop...

See similar textbooks

Similar questions

Water flows at a rate of 0.040 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8 cm by a reducer. If the pressure at the centerline is measured to be 480 kPa and 440 kPa before and after the reducer, respectively, determine the irreversible head loss in the reducer. Take the kinetic energy correction factors to be 1.05.
Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8 cm by a reducer. If the pressure at the centerline is measured to be 480 kPa and 457.3 kPa before and after the reducer, respectively, determine the pressure loss in the reducer. Take the density of water to be ρ = 1000 kg/m3 Ans: [22,300 Pa]
A large tank is initially filled with water 4 m above the center of a sharp-edged 10-cm-diameter orifice. The tank water surface is open to the atmosphere, and the orifice drains to the atmosphere. If the total irreversible head loss in the system is 0.2 m, determine the initial discharge velocity of water from the tank. Take the kinetic energy correction factor at the orifice to be 1.2.
Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8 cm by a reducer. If the pressure at the centerline is measured to be 480kPa and 445 kPa before and after the reducer, respectively, determine the head loss in the reducer.
A 3-m-high large tank is initially filled with water. The tank water surface is open to the atmosphere, and a sharp-edged 10-cm-diameter orifice at the bottom drains to the atmosphere through a horizontal 80-m-long pipe. If the total irreversible head loss of the system is determined to be 1.5 m,In order to drain the tank faster, a pump is installed near the tank exit. Determine the pump head input necessary to establish an average water velocity of 6.5 m/s when the tank is full.
In a hydroelectric power plant, 100 m3/s of water flows from an elevation of 120 m to a turbine, where electric power is generated . The total irreversible head loss in the piping system from point 1 to point 2 (excluding the turbine unit) is determined to be 35 m. If the overall efficiency of the turbine–generator is 80 percent, estimate the electric power output.
Water flows at a rate of 20 L/s through a horizontal pipe whose diameter is constant at 3 cm. The pressure drop across a valve in the pipe is measured to be 2 kPa, as shown. Determine the irreversible head loss of the valve, and the useful pumping power needed to overcome the resulting pressure drop
Water flows at a rate of 0.040 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8 cm by a reducer. If the pressure at the centerline is measured to be 480 kPa and 442 kPa before and after the reducer, respectively, determine the irreversible head loss in the reducer. Take the kinetic energy correction factor to be 1.05. Take the density of water to be ρ = 1000 kg/m3.
Water enters a hydraulic turbine through a 30-cm-diameter pipe at a rate of 0.7 m3/s and exits through a 25-cm-diameter pipe. The pressure drop in the turbine is measured by a mercury manometer to be 1.2 m. For a combined turbine–generator efficiency of 83 percent, determine the net electric power output. Disregard the effect of the kinetic energy correction factors. Take the density of water to be 1000 kg/m3 and the density of mercury to be 13,560 kg/m3.
A 78-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.7 ft3/s through a constant-diameter pipe. The free surface of the pool is 32 ft above that of the lake. Determine the irreversible head loss of the piping system, in ft, and the mechanical power used to overcome it. Take the density of water to be 62.4 lbm/ft3.
The drinking water needs of an office are met by large water bottles. One end of a 0.6-cm diameter plastic hose is inserted into the bottle placed on a high stand, while the other end with an on/off valve is placed 0.6 m below the bottom of the bottle. If the water level in the bottle is 0.45 m when it is full, determine how long it will take at the minimum to fill a 0.25-L glass when the bottle is first opened. Neglect frictional and valve losses.
The water level in a tank is 70 ft above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the water pressure by 15 psia. Determine the maximum height to which the water stream could rise.