A diesel power station has the following data Fuel consumption/day = 1000 kg Units generated/day = 4000 kWh Calorific value of fuel = 10,000 kcal/kg Alternator efficiency = 96% Engine mech. efficiency = 95% Estimate: (i) (ii) (iii) (iv) specific fuel consumption, overall efficiency, engine efficiency thermal efficiency of engine.

A diesel power station has the following data Fuel consumption/day = 1000 kg Units generated/day = 4000 kWh Calorific value of fuel = 10,000 kcal/kg Alternator efficiency = 96% Engine mech. efficiency = 95% Estimate: (i) (ii) (iii) (iv) specific fuel consumption, overall efficiency, engine efficiency thermal efficiency of engine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air-standard diesel cycle engine operates as follows: inlet temperature, 30°C; temperature after compression, 700°C; net cycle work, 5901.1 kJ/kg; and heat added per cycle, 925 kJ/ kg. Determine the cycle state points and work net.
A rankine turbo-generator unit receives 27,000kg/hr. of steam at 1.20 MPa and superheated by 122 degrees. condensate leaves at 22 degree celsius, for brake steam rate WB= 4.74 kg/kwhr, mechanical efficiency of 90% and generator efficiency = 94%. Determine the A) ideal work B) Work net C) Ec, cycle thermal efficiency D) W indicated E) indicatedsteam rate F) Indicated engine efficiency G)turbo generator output in KW(Wk)
Subject: Combustion Engineering A rankine cycle has the specific conditions: Inlet of turbine: T= 368 degree celcius p= 11.17 mPa condenser pressure= 550 kpa For specific volume and density, use steam table. g= 9.81 m/s² Consider water to be incompressible, do not neglect the pump work. For below parameters: mass flow rate= 1.5 kg/s length (L) in meters diameter (D) in meters L= 4D-1 meters What is the value of the diameter (except 0) in cm that will give the maximum headloss?
Thermodynamics (Carnot Cycle) An OTEC power plant has an efficiency of 2.5%. The difference in temperature of teh warm surface water (hot source) and cold deep-water (sink) is 7.5℃. Assuming powerplant is operating in a Carnot Cycle, find the temperature of the sink in ℃. Options: a. 11.5 b. 12.5 c. 13.5 d. 14.5 e. 15.5 f. 16.5 g. 17.5 h. 18.5 i. 19.5 j. None of the above
Provide a complete and logical solution for the problem. If linear interpolation is required in the problem, tabulated values is considered as a solution. Also, provide T-S or P-V diagrams for each problem. For a Rankine Cycle, steam at 5.25 MPa, 435°C expands to 0.036 MPa. For 10 kg/s of steam, determine: a. Heat added b. Heat rejected c. Work of turbine d. Thermal Efficiency
A Rankine Engine-Generator unit receives 27,000 kg/hr of steam at 1.2 MPa and 150°C and exhausts to a condenser temperature of 22 C. Brake steam rate is 4.74 kg/kW-hr, mechanical efficiency is 90 % and generator efficiency is 94 %. Determine: a) ideal cycle thermal efficiency, b) indicated engine efficiency, c) generator output (kW), d)the condition of turbine actual exhaust
Solve for the efficiency of Process 1-2-6-5 (Simple Rankine Cycle) (orange circle) *Not the reheat rankine cycle Efficiency for Simple Rankine Cycle = 35 % (probable answer)
Pls answer thank you! The following data were obtained during performance test with a simple open cycle gas turbine engine: compressor inlet temperature, 520*R: compressor isentropic discharge temperature, 672"R: actual compressor discharge temperature, 691"R: turbine inlet temperature, 1500 R: turbine isentropic discharge temperature. 1184"R: and turbine actual discharge temperature, 1216°R. For these conditions calculate the thermal efficiency in percent.
The properties of this Organic Rankine Cycle are as follows: • Turbine feed: P = 24.49 bar, T = 272.19C• Turbine exhaust: P = 2 bar, T = 203C. Assume ideal gas at P = 2 bar. • The pump efficiency is 65%.• Benzene is used as the working fluid Calculate the turbine shaft work Ws,turbine (in J/mol).
Rannkin cycle 1_The value of enthalpy at point 1 is ( h1 =?) 2_ value of enthalpy at point 2 is ( h2 =?) 3_ value of enthalpy at point 3 is ( h3 =?) 4_value of enthalpy at point 4 is ( h4 =? 5_ value of steam mass flow rate in kg/s is 6_rate of heat supplied7_ power developed by Turbine (WT) in kW is : 8_ Thermal efficiency of Rankine cycle is:
Explain briefly the operating conditions which affect Rankine cycle efficiency. What are the methods of improvement?
Write legibly, provide manual step by step solution, and diagram for below given problem. A superheat steam Rankine cycle has turbine inlet conditions of 17.5 Mpa and 530 C expands in a turbine to 0.007Mpa. The turbine and pumps polytropic efficiencies are 0.9 and 0.7 respectively, pressure losses between pump and turbine are 1.5MPa. What should be the pump work in KJ/kg? A. 17.3 C. 37.3 B. 27.3 D. 43.4