A diver of weight 470 N stands at the end of a diving board of length L = 4.8 m and negligible mass (the figure). The board is fixed to two pedestals separated by distance d = 1.0 m. Take the upward direction to be positive. Of the forces acting on the board, what are (a) the force from the left pedestal and (b) the force from the right pedestal? -P (a) Number i Units (b) Number i Units

A diver of weight 470 N stands at the end of a diving board of length L = 4.8 m and negligible mass (the figure). The board is fixed to two pedestals separated by distance d = 1.0 m. Take the upward direction to be positive. Of the forces acting on the board, what are (a) the force from the left pedestal and (b) the force from the right pedestal? -P (a) Number i Units (b) Number i Units

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter8: Rotational Equilibrium And Rotational Dynamics

Section: Chapter Questions

Problem 8WUE: A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and...

See similar textbooks

Similar questions

A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.
A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands. Im stuck on this q, pls help.
A person carries a plank of wood 2.00 m long with one hand pushing down on it at one end with a force F1 and the other hand holding it up at .500 m from the end of the plank with force F2 . If the plank has a mass of 20.0 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1 and F2 ?
Why is the following situation impossible? A uniform beam of mass mb = 3.00 kg and length ℓ = 1.00 m supports blocks with masses m1 = 5.00 kg and m2 = 15.0 kg at two positions as shown. The beam rests on two triangular blocks, with point P a distance d = 0.300 m to the right of the center of gravity of the beam. The position of the object of mass m2 is adjusted along the length of the beam until the normal force on the beam at O is zero.
An auto magazine reports that a certain sports car has 53% of its weight on the front wheels and 47% on its rear wheels. (That is, the total normal forces on the front and rear wheels are 0.53w and 0.47w, respectively, where w is the car’s weight). The distance between the axles is 2.46 m. How far in front of the rear axle is the car’s center of gravity?
A person carries a plank of wood 1.9 m long with one hand pushing down on it at one end with a force F1 and the other hand holding it up at 49 cm from the end of the plank with force F2. If the plank has a mass of 18 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1 and F2? (The distance of 49 cm is measured from the location of F1.)
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force η1 on the beam, and the second pivot located a distance ℓ = 4.00 m from the left end exerts a normal force η2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as shown. The goal is to find the woman’s position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forcesacting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force η1 is the greatest? (d) What is η1 when the beam is about to tip? (e) Use as shown to find the value of η2 when the beam is about to tip.(f) Using the result of part (d) and as shown, with torques computed around the second pivot, find the woman’s position x…
A uniform beam of length L = 2.2 m and mass M = 33 kg has its lower end fixed to pivot at a point P on the floor, making an angle θ = 15° as shown in the digram. A horizontal cable is attached at its upper end B to a point A on a wall. A box of the same mass M as the beam is suspended from a rope that is attached to the beam one-fourth L from its upper end.What is the y-component Py of the force, in newtons, exerted by the pivot on the beam? Py = Write an expression for the tension T in the horizontal cable AB. T = What is the x-component Px of the force, in newtons, exerted by the pivot on the beam? Px =
A hinged beam, 92.5 kg, is supported by a horizontal cable as in the figure. The length of the cable is 2.00 m and the length of the beam is 3.00 m. Find: (a) the torque produced by gravity on the beam, (b) the tension in the cable, (c) the horizontal and vertical components of the force from the hinge, and (d) the magnitude and direction of the force from the hinge.
a uniform beam of length 12.0 m is supported by a horizontal cable and a hinge at angle u =50.0°. The tension in the cable is 400 N. In unit-vector notation, what are (a) the gravitational force on the beam and (b) the force on the beam from the hinge?