Answered: A dwelling with a general lighting load…

A dwelling with a general lighting load of 10,000 VA requires a minimum of how many 15 A branch circuits? A. 10 B. 3 C. 8 D. 6

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 10PP: In an R-L parallel circuit, ET=240 volts, R=560, and XL=330. Find apparent power.

See similar textbooks

Related questions

Q: for this circuit (a) Identify and label the number of nodes in the circuit. (b) How many branches…

A: Nodes : A node is any place on a circuit between two circuit elements in electrical engineering.…

Q: List down 4 units of light and define it shortly. 2. Briefly explain the 3 types of lamps. 3.…

A: Introduction: The intensity of light per unit area is called as illumination. "Lux", in the…

Q: A lidless with square ends is to be made from a thin sheet of metal. Determine the least area of…

Q: 1. Which diagram is helpful in designing, constructing and troubleshooting or repairing an…

A: Given, We have two mcqs on diagrams to represent electrical and electronic circuits. Please find the…

Q: What are the loads that are allowed and are not allowed to connect to a general socket based on its…

A: Given: General socket question

Q: A football field, an area of 60 x 120, is a fridge to be lit at night with 1000 W lamps, provided…

A: KIRCHHOFF’S LAW KCL: The algebraic sum of all currents at a node is zero. KCL is applicable for…

Q: Could several panels be placed in parallel in order to increase the power of the system? What…

A: Yes, if numerous panels are connected in parallel, the system's power is increased. When solar…

Q: The dwelling has a floor area of 142 sq. m. It has a typical household appliance including one 8 kW…

A: A dwelling unit is a place used for providing living accommodations, the place is not a hotel, but…

Q: 16.a. When installing cable behind a wall, it's recommended to run the cable behind the baseboard…

Q: 3/You are a network administrator and you need to subnet your network to five subnetworks consisting…

A: The explanation is as follows.

Q: what is the minimum kW service demand load for twenty 6.5-kW electric ranges in a multifamily…

A: In this question what is the minimum kW service demand load for twenty 6.5-kW electric ranges in a…

Q: explain Branch circuit protection can be provided in the field under what circumstances? a. Branch…

A: Here we discuss about the branch circuit.

Q: We want to install the 2000-meter wire in the college building, which one testing is the most…

A: Here, we required to install the 2000-meter wire in the college building.

Q: items that contribute to Earth Resistance for your grounding system and what can be done to minimize…

Q: What color code designates a 12, 10% resistor? What color code designates a 1k Q, 5% resistor? What…

Q: 1) Definition of low voltage network 2)What are low voltage network types ? - Explaining of every…

A: Note :As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: for this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1) General Emergency Power Systems provide automatic backup power in the event of normal power…

Q: A dining area is planned for its lighting lay out. It has a dimension of 4x3m. If the owner wishes…

Q: In order for mutual exclusion to prevail in the system, the following conditions must be met

A: Mutual exclusion (mutex) is a program object that prevents simultaneous access to a shared resource.…

Q: Question 2 (a) a) Mr. jojo, lives in a four flat house, the conditions of the lighting system was…

A: let us consider three wall switches are there front door(A), one at the back door(B) and one in the…

Q: An electric heating element has a resistance of 16 Ω and is connected to a voltage of 120 V. How…

A: Given data: E=120 VR=16 Ω

Q: . Is it possible to install 12 lightings in one circuit?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: A dining area measuring 4x4m is planned for its lighting lay-out. The owner wishes to install…

Q: supplementary grounding electrode is required when the only grounding electrode available is ? NEC…

A: According to NEC 250.53 (D)(2) A supplementary grounding electrode is required if metal…

Q: b) Various methods and techniques are used to monitor and control a project to make sure it runs…

A: Areas of knowledge required are as follows- 1- Should know how to deal properly with electricity…

Q: Using the Mesh Current Method, what is the value of VA?

Q: 5.a. The labor performed when you extend an existing electrical system is called A. old work.…

Q: Given: A single family dwelling with a floor area of 120 sq.m., 220 volts 2 wire line to ground, and…

A: Consider the given information, The floor area of the room is 120 sq.m. Lighting loads are : 8 lamps…

Q: How many socket-outlet circuits are required if a house requires twenty (20) socket-outlets? And…

A: It is asked how many socket-outlet circuits are required if in a house requires total 20…

Q: You are required to explain in more detail about the information based on the circuit and graph…

A: According to the question, we need to explain the operation of the circuit based on the graph.

Q: 1. List the items that contribute to Earth Resistance for your grounding system and what can be done…

A: The factors that contribute towards the earth resistance for the grounding system are as…

Q: Raceway fill calculations are a prerequisite in ____ needed for particular circuits. Select one: A.…

A: Raceway fill calculations are a prerequisite in determining the size of the raceway needed for…

Q: A house has the following specifications for a circuit. Determine the size of the circuit breaker,…

A: For a circuit, a house has the following specifications, 15 lighting outlets1 kitchen range12…

Q: 1. Draw a cut-away pictorial view of a single room (your own lay out) with a separate circuits…

A: Pictorial View: Typical Mounting Height: Duplex con. Outlet/Receptacle outlet- 18'' (45cm)…

Q: List the items that contribute to Earth Resistance for your grounding system and what can be done to…

A: List of the items which contribute to the earth resistance for the grounding system are named below:…

Q: Please answer the "required" portion. Show full solutions with brief explanations and please DRAW…

Q: - For the circuit shown below, determine the values of the voltages Vx and Vo; and currents in, i2,…

Q: 5. If the resistor is doubled in the circuit on item number 4, what is the load current?

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: What is the equivalent resistance between A – C points in the circuit shown? A 21Ω B 2,8 Ω C…

Q: Question 8.a Which article of the NEC describes the proper placement of outlets in this type of…

A: The Given is article of the NEC describes the proper placement of outlets in this type of room.

Q: Given: A single family dwelling with a floor area of 120 sq.m., 220 volts 2 wire line to ground, and…

A: Given: A single family dwelling with a floor area of 120m2, 220 volts 2 wire line to ground, and…

Q: Electric metal tubing (EMT) provides protection from ____. Select one: A. INADVERTENT GROUNDING B.…

Q: Calculate the dc voltages and currents in the circuit of

A: Given circuit is in the DC bias condition so

Q: What is the full form of NEC? What is it's purpose

A: Full form of NEC is National electrical codes. it plays a vital role in the in the installation of…

Q: superposition method be used to advantage?

Q: microwave oven is connected to a 250V supply for 2 hours with a power rating of 1.8kW. Find the…

A: A microwave oven is connected to a 250V. Time T=2 hours power rating P=1.8kW. Find the total…

Q: 2. Can you draw another circuit for clipping with out using VR giving the same results ?

A: We saw in the Signal Diodes tutorial that when a diode is forward biased it allows current to pass…

Concept explainers

Graph theory

It is that part of network analysis where the configuration is called graph or structure of the network system when all of the elements (e.g., R, L, and C) in a network system are substituted with lines having circles/rings or dots across both endpoints. The study of the solution of the networks and circuits with the help of graphs is known as graph theory. The objective is to know the mathematics behind the network analysis.

Question

A dwelling with a general lighting load of 10,000 VA requires a minimum of how many 15 A branch circuits?

A. 10

B. 3

C. 8

D. 6

Expert Solution

Step 1

In this answer let us find out the number of 15 amp branch circuits that are required for a dwelling with general light load of 10000 VA as explained below.

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load is connected to a network. At the terminals to which the load is connected, Rth = 10 Ω and Vth = 40 V. The maximum possible power supplied to the load is
A small plant has been constructed and the costs are known. A new plant is to be estimated with the use of the exponential (power sizing) costing model. Major equipment, costs, and factors are as shown in the shown table. (Note MW = 106 Watts.) If ancillary equipment will cost an additional $200,000, find the cost for the proposed plant.
5. A power plant customer draws power at 220V from transformers on a pole. Current transformers with ratio of 200/5 are used to meter the electrical usage. What is the multiplier of the kW-hr and demand meters?
use these values: Vs=130 R=280
what is the minimum neutral demand load in (kw) for 12 apartments, each containing an 8-kw range
A 100 ohm (0 oC) RTD has a temperature coefficient of α= 0.00385 Ω/ Ω/ oC. What is the resistance of the RTD at temperature 550 oC? 211.11 213.54 411.34 311.75 102.11
1. An Industrial load is taking 500kW at 0.6 lagging pf. It is desired to raise the pf to 0.866 lagging usingsynchronous machines whose power input is 300-kW. Calculate the KVA rating of the motor required forsuch operation and the power factor at which the motor will operates.
Urgent. An office space measures 50ft x 90ft with 16ft high walls. A 1.25 air changes per hours is desired for this space. Find the heat loss (in btuh) when the indoor temperature is 70°F and the outdoor temperature is 36°F. Select one: a. Q = 56,100 btuh b. Q = 44,880 btuh c. Q = 37,736 btuh d. Q = 75,900 btuh e. Q = 64,350 btuh
Calculate R and the power supplied by the 500V source.
A barangay power station supplies 60kW to a load over 2,500ft, 100 mm², two conductors copper feeder. The resistance of which is 0.0078 ohm per 1,000 ft the bus bar voltage is maintained constant at 600V. Determine the load current.
The load that can be used for the service calculation for a dwelling unit with a range rated at 13 KW is which of the following: 13 kw 8.4 kw 8 kw 5.5 kw
Calculate the average load on a steam power station which spends (47x10°) IDQ (Iraqi Dinar) per year for fuel used in the station. The calorific value of 5000 kcal/kg and its price is (4700) IDQ per ton. The thermal efficiency of the station is 35% while electrical efficiency is 85%.