A family is preparing dinner and a pizza is being toasted in an oven whose wall is ma a 0.5-cm-thick layer of steel (ks = 15 W/m·K) and a layer of brick (kb = 0.72 W/m.k steady state, the oven inner surface temperature of the steel layer is 450°F, a temperature drop of 0.5°C occurs across the steel layer. If the temperature of the surface of the brick must be no greater than 40°C for safety concerns, determine thickness of brick in cm, that ensures this limit is met. What is the rate of conduction called boat flund in /(m²?

A family is preparing dinner and a pizza is being toasted in an oven whose wall is ma a 0.5-cm-thick layer of steel (ks = 15 W/m·K) and a layer of brick (kb = 0.72 W/m.k steady state, the oven inner surface temperature of the steel layer is 450°F, a temperature drop of 0.5°C occurs across the steel layer. If the temperature of the surface of the brick must be no greater than 40°C for safety concerns, determine thickness of brick in cm, that ensures this limit is met. What is the rate of conduction called boat flund in /(m²?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.36P

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
J 5 A cylindrical steel tank with a diameter of 1.8m and a height of 2m, is insulated with polyurethane on its lateral faces and its lid. The insulation is 40 mm thick and covered with a thin layer of metal. The tank contains water that is kept warm by an electric heater in such a way as to maintain the inner surface of the tank at a temperature of 55C. The ambient air temperature is 10C and the external skin coefficient is 10 w/m2K. If the energy cost is $0.15/kwh. What is the monthly energy cost for water storage?
A domestic refrigerator with inner dimensions of 0.7 m by 0.7 m at the base and height 1 m was designed to maintain a set temperature of 6 ˚C. The bodies consist of two 10-mm-thick layers of Aluminium (k = 225 W/mK) separated by a 30 mm polyurethane insulation (k=0.028 W/mK). If the average convection heat transfer coefficient at the inner and outer surfaces are 11.6 W/m2K and 14.5 W/m2K respectively, calculate: the outer surface temperature of the Aluminum in 0C to 2 decimal places
Steam at a temperature of 723 K is flowing through a pipe with an outer diameter of 100 mm. The pipe is insulated with 30-mm thick mineral wool, the average thermal conductivity of which is 0.065 W/m.K. Determine the outside surface temperature of mineral wool if the ambient air temperature is 300 Assume the hot-surface temperature of the mineral wool is the same as that of the flowing steam and the value of the surface coefficient of the insulating material is 33 W/m2.K.
Partially-frozen ice cream is being placed in a package before completion of the freezing process. The package has dimensions of 8 cm by 10 cm by 20 cm and is placed in air- blast freezing with convective heat coefficient of 50 W/(m2 K) for freezing. The product temperature is -5°C when placed in the package, and the air temperature is -25°C. The product density is 700 kg/m3, the thermal conductivity (frozen) is 1.2 W/(m K), and the specific heat of the frozen product is 1.9 kJ/(kg K). If the latent heat to be removed during blast freezing is 100 kJ/kg, estimate the freezing time.
1. (a) Consider a room with a 1.8-m-high and 2.0-m-wide double-pane window consisting of two 4-mm-thick layers of glass separated by a 10-mm-wide stagnant air space. The convection heat transfer coefficients on the inner and outer surfaces of the window are 12 W/m2 K and 25 W/m2 K, respectively, while the average thermal conductivity of glass is 0.78 W/m K; and the air, 0.026 W/m K. If the room is maintained at 22 oC, the outside temperature is -4 oC and heat transfer due to radiation can be neglected, determine: (i) Draw the sketch and thermal resistance network; (ii) the total thermal resistance; (iii) the steady rate of heat transfer through this double-pane window; (iv) the temperature of the inner surface of the window.…
A long stainless-steel (AISI 316) steam pipe, with an inside diameter of 6.00 cm and an outside diameter of 8.00 cm, is covered with a layer of asbestos insulation (k = 0.150 W/m-K) 1.00 cm thick, which in turn is covered with foam insulation (k = 0.044 W/m-K) 6.00 cm thick. The inside surface temperature of the stainless-steel steam pipe is measured to be 250.0°C, while the outside surface of the foam is exposed to convection, T_inf = 25.0°C, h_inf = 15.0 W/m^2-K. • Draw and label a sketch of this system. Include dimensions, known temperatures, etc. • Draw and completely label the corresponding 1-D steady-state conduction resistor diagram. • Determine the heat transfer rate through the pipe per unit length. • Calculate the temperature at the asbestos/foam interface.
Chips of width L _ 15 mm on a side are mounted to a substrate that is installed in an enclosure whose walls and air are maintained at a temperature of Tsur=T∞=25oC. The chips have an emissivity of ε=0.60 and a maximum allowable temperature of Ts=85oC. (a) If heat is rejected from the chips by radiation and natural convection, what is the maximum operating power of each chip? The convection coefficient may be approximated as h=11.7 W/m2K. (b) If a fan is used to maintain airflow through the enclosure and heat transfer is by only forced convection, with h=250 W/m2K, what is the maximum operating power
An industrial freezer is designed to operate with an internal air temperature of -20°C when the external air temperature is 27°C, and the internal and external heattransfer coefficients are 8 W/m2 -K and 12 W/m2 -K, respectively. The walls of thefreezer are composite construction, comprising an inner layer of plastic (k = 0.33 W/m-K, and thickness of 10 mm), and an outer layer of stainless steel (k = 15 W/m-K, and thickness of 3 mm). Sandwiched between these two layers is a layer of insulation material with k = 0.07 W/m-K. Find the width (mm) of the insulation thatis required to reduce the convective heat loss to 60 W/m2.
Clothing made of several thin layers of fabric with trapped air in between, often called ski clothing, is commonly used in cold climates because it is light, fashionable, and a very effective thermal insulator. So it is no surprise that such clothing has largely replaced thick and heavy old-fashioned coats. Consider a jacket made of five layers of 0.1-mm-thick synthetic fabric (k = 0.13 W/m·K) with 1.5-mm-thick air space (k = 0.026 W/m·K) between the layers. Assuming the inner surface temperature of the jacket to be 28°C and the surface area to be 1.25 m2, determine the rate of heat loss through the jacket when the temperature of the outdoors is 0°C and the heat transfer coefficient at the outer surface is 25 W/m2·K. What would your response be if the jacket is made of a single layer of 0.5-mm-thick synthetic fabric? What should be the thickness of a wool fabric (k = 0.035 W/m·K) if the person is to achieve the same level of thermal comfort wearing a thick wool coat instead of a…
Question 1: A glass window of width W = 1 m and height H = 2 m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 oC and -20 oC, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of 20 oC and -15 oC, what is the rate of heat loss from a 1 m x 2 m window? The thermal conductivity of air is ka = 0.024 W/m.K.
A steam turbine casing is made of a 6mm thick steel plate. At one location it has an inside surfacetemperature of 100°C. The convective heat transfer coefficient on the outside is 10 W/m2K. Theambient temperature is 25°C. What is the outer surface temperature? If the outer surface iscovered with a 3cm layer of insulation (k = 0.04 W mK), will it be safe to touch? Explain.