A gear and pinion system (N = 16 and 48 each) of Grade 1 steel is to transmit 5 hp under uniform shock and has the following parameters: Pressure angle = 20° Pinion speed = 210 rpm Pinion diametral pitch = 6 teeth/ in Face width = 2.75 in Hardness = 250 Brinell Quality = 7 Reliability = 0.99 Determine the safety factors for contact and bending for both the gear and the pinion. List out the correction factors that you assumed = 1.

A gear and pinion system (N = 16 and 48 each) of Grade 1 steel is to transmit 5 hp under uniform shock and has the following parameters: Pressure angle = 20° Pinion speed = 210 rpm Pinion diametral pitch = 6 teeth/ in Face width = 2.75 in Hardness = 250 Brinell Quality = 7 Reliability = 0.99 Determine the safety factors for contact and bending for both the gear and the pinion. List out the correction factors that you assumed = 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There are two pairs of closed soft tooth surface spur gears A and B,Parameters of A: modulus m = 2mm, number of teeth Z1 = 40, Z2 = 90 , width of teeth b = 60mm.Parameters of B : modulus m = 4mm, number of teeth Z1 = 20, Z2 = 45 , width of teeth b = 60mm.The accuracy of the two pairs of gears is grade8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason.
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20° Assuming that only one pair of the teeth is in contact the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is...
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
A three-thread worm gear, rotating at 1000 rpm, drives a 31-tooth worm gear and transmit 15 HP. Theworm has 14 ½ o teeth with ¾ pitch, 2 in pitch diameter, and an included face angle of 60o. The coefficientof friction is 0.05. (Assume Y = 0.322) A. Determine the helix angle of the worm. Ans. 70.30o B. Determine the speed ratio. Ans. 10.33C. Determine the center distance. Ans. 4.70 inD. Determine the apparent stress in the worm wheel teeth. Ans. 31,100 psiE. Determine the efficiency of this worm-gear set. Ans. 85.70%
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?
power (N)=9.9kw Input speed (n1)=2350rpm Distance between centers (a)=168mm Total distance between Ave B bearings=440mm module(m)=3mm question 3 Calculate the power on the output shaft since there is 3% loss in gears in gearboxes, rolling bearings in support bearings (2% loss in a pair of bearings) and sealing element spring seal (4% loss in a pair of sealing elements).
Q3/ A vertical double acting steam engine develops 80 kW at 240 rpm. The maximum fluctuation of energy is 25% of the work done per stroke. The maximum and minimum speeds are not to vary more than +1% of the mean speed. Find the mass of the flywheel, if the radius of gyration is 0.65 m.
A model of hydraulic turbine, to scale of 1/5 is tested under a head of 7.5m. The prototype works under a head of 180 m and is to run at 500 rpm. At what speed should the model be operated?
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
3. The nominal power of the wind turbine is 3MW at wind speed 11.5m/s, generator efficiency is 94%, gear box efficiency is 0.75, power coefficient of blades is 0.59. What would be the diameter of the rotor?