A hydraulic oil is flowing in a horizontal drawn steel hydraulic tube (ɛ = 1.5 x 10 -"m) with an ID of 0.047m. A pressure difference of 68 kPa isobserved between two points in the tube 30 meters apart. The oil has a specificgravity of 0.90 and a dynamic viscosity of 3.0 × 10-³Pa ·s. Calculate the velocityof the flow of oil using Method Il-C iteration.

The given data is shown below: ε=1.5×10-6 mInner diameter=0.047 mPressure difference=68 kPaSpecific…

Answered: A hydraulic oil is flowing in a…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5.10 The water is supplied at the rate of 3 m3 per minute from a height of 4 m to a hydraulic ram, which raises 0.3 m3/minute to a height of 30 m from the ram. The length and diameter of the delivery pipe is 100 m and 70 mm respectively. Determine the D' Aubuisson's efficiency of the hydraulic ram if the co-efficiency of friction f = .009.
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from the reservoir and through the pipe shown in the Fig. below. Compute the pressure at point B, considering the energy loss due to friction, but neglecting other losses. Also, use pipe roughness of 1.50 X 10-6 m. Hint: Use the appropriate formula to determine the friction factor, f to 4 decimal places (flow type dependant); g = 9.81 and round off to 3 decimal places for all other step calculations leading to the final answer including the final answer.
Water at 15°C (? = 999.1 kg/m3 and ? = 1.138 × 10−3 kg/m·s) is flowing steadily in a 30-m-long and 6-cm-diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop.
an open circular vessel is 1m in diameter and 2m height. it contains water filled to a depth of 1.5m. if the cylinder rotates about its vertical axis, what is the pressure intensity at the corner of the bottom if w= 6 radians/second Unit of the correct answer: kPa
Calculate the diameter of vertical pipe needed for flow of liquid at R = 1800 when the pressure remains constant. v = 1.5 um?/s.
Velocity (Pipe 1), Velocity (Pipe 2) [m/s] .Velocity (Pipe 3) [m/s] ,Entrance loss (Reservoir 1 & Pipe 1) [meters], Friction loss (Pipe 1) [meters]
Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s.
A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
A horizontal pipe of 150 mm diameter for the initial 30 m and 75 mm dimeter for the remaining 10 m is connected to a water tank. The height of waler in tank is 15 m above the centre line of the pipe. Find out the flow rate through the pipe, taking all losses into the account. Consider the reduction in diameter of the pipe as sudden coefficient of friction for the pipe is 0.008.
The container is partially filled with oil. Water and air as shown. Determine the pressure at A, B and C assuming Pwater=1000kg/m^3 and Poil=830 kg/m^3

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS