A hydroelectric power plant is to be built at a dam with a gross head of 240 m. The head losses in the head gate and penstock are estimated to be 6 m. The flow rate through the turbine is 18,000 L/min. The efficiencies of the turbine and the generator are 88 percent and 96 percent, respectively. The electricity production from this turbine is (a) 6930 kW (b) 5750 kW (c) 6440 kW (d ) 5820 kW (e) 7060 kW

Q: Consider two hydraulic turbines having identical specific speed and effective head at the inlet. If…

A: Given data: - The speed ratio of the two turbines is N1/N2 = 2. The expression for the specific…

Q: Is the flow expected to be uniform or nonuniform for frictionless pipes? Why

A: according to the given details in the question.

Q: Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the…

A:

Q: What is mechanical efficiency? What does a mechanical efficiency of 100 percent mean for a hydraulic…

A: Mechanical efficiency: Mechanical efficiency is defined as the comparison of the energy at the inlet…

Q: In a hydroelectric power plant, 100 m3/s of water flows from an elevation of 120 m to a turbine,…

A: Given data: *The volume flow rate of the water is V=100 m3/s. *The elevation of the flow of water to…

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A: Q=0.01m3/shL=13.0 mρ=1000kg/m3μ=0.001kg/m.s

Q: Which of the following head is neglected in ideal Bernoulli's Energy equation O 1. Head loss due to…

A:

Q: What is the operation and components of an aircraft engine driven hydraulic pump?

A: given; What is the operation and components of an aircraft engine driven hydraulic pump?

Q: Calculate the water power available in the pipe flowing at the rate of 0.166 m3/s with total Head as…

A: Given, Discharge , Q=0.166m3/sTotal head, h=29.9mDensity of water, ρ=1000kg/m3acceleration due to…

Q: In a hydroelectric power plant as shown in the figure, 100 m3/s of water flows froman elevation of…

A: Given Volumetric flow = 100 m3/s Elevation = 130 m Overall efficiency = 0.8 % To find Electric power…

Q: pump shown in Fig. P8.75 delivers a head of (hp) 250 m to the water. Determine the power that the…

A:

Q: Water (γwater = 9810 N/m3) drains from the reservoir higher to the bottom, both with constant…

A:

Q: Water from a reservoir is pumped over a hill through a pipe 30 cm in diameter, and a pressure of 250…

A: Given dataDiameter of the pipe d = 30cmPressure P = 250kPaHead maintained H= 100mHead loss due to…

Q: 8–90 Water at 15°C is to be pumped from a reservoir (ZA = 2 m) to another reservoir at a higher…

A:

Q: For a piping system, define the system curve, the characteristic curve, and the operating point on a…

A: Draw the system curve, the characteristic curve, and the operating point on a head versus flow rate…

Q: Determine the loss of head due to sudden enlargement when the velocity of water in the smaller pipe…

A:

Q: . In reference to problem number 1, if another pump was used having a power requirement of 12 hP…

A: Concept:-  It is a fliud machinery question in which pump is delivering the water at a certain…

Q: Water is flowing through a circular pipe made of cast iron with a diameter of 26 cm. If Reynolds…

A: Given,  Flow of water through pipe Reynolds number (Re) = 105 Concept: Since Reynolds number (Re)…

Q: A 15-cm pipeline, 730 m long, has its discharge end 6 m below the water surface in the reservoir…

A:

Q: A submersible pump with a shaft power of 5 kW and an efficiency of 72 percent is used to pump water…

A: Given data as per the question Shaft power of submersible pump =5 KW Efficiency = 72% Height of free…

Q: In a distribution system, Reservoir A supplies water to a branched system with Reservoir B and…

A: A reservoir is a man-made mechanism for storing water. The majority of reservoirs are created by…

Q: Water is pumped from a large lower reservoir to a higher reservoir. Someone claims that if the head…

A: let us considering a system in which a pump is used to lift water from point 1 to point 2. applying…

Q: A turbine is placed at the bottom of a 20-m-high water body. Water flows through the turbine at a…

A: Given: The height of the body is H=20 m. The rate of flow of the water is V=30 m3/s. The shaft power…

Q: In a Francis turbine, the pressure gage in the turbine casing reads 480 kpa. The elevation above the…

A: The pressure gage in turbine casing, P = 480 kPa The elevation above the tailrace to the center of…

Q: What is the overall efficiency of the turbine if the power developed is 15,000 kW at a head of 150…

A:

Q: In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.55 m3/s…

A: From tables properties of water, ρ = 998 kg/m3 μ = 1.002 x 10-3 Pa s Roughness of cast iron pipe is…

Q: Explain how flow rate is measured with a turbine flowmeter, and discuss how they compare to other…

A: For measuring flow rate we have many flow meter and one of them is Turbine flow meter. As from the…

Q: Water flows with a flow rate of 0.035 m³/s through a horizontal pipe whose diameter is reduced from…

A: Solution:

Q: The water in an aquarium will be drained for cleaning. A flexible tube (D = 5mm) will be used to…

A: Given data, D= 5 mm = 0.005 m  Vertical distance z1= 60 cm = 0.6m  Considering datum at end of tube…

Q: Q.3) Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of…

A: Givenpower provided by pump to water P=20kWZ=45mhL=23m

Q: Which choice is correct for the comparison of the operation of impulse and reaction turbines? (a)…

A: Impulse turbines: Impulse turbines are those in which the fluid directly impinges to rotating blades…

Q: Heavy fuel oil is pumped at a flow rate of 88 L/s through a new steel pipe. What diameter of the…

A:

Q: The water is to be pumped from the lower reservoir to the upper reservoir at a flow rate of 8 kg/s.…

A: Pump  Pump is a hydraulic device which is used to lift liquid from low height to the high elevation.…

Q: 02: Water is to be withdrawn from a 3 m high water reservoir by drilling a 1.5 cm diameter hole at…

A:

Q: kindly help me with this problems INSTRUCTIONS: Solve the  problems neatly and systematically. S…

A: Given,

Q: In a large pumped hydro plant, the head from the turbine to the lake surface is 100m. During a…

A: Given : P = 50 MW η=0.7 h = 100 m t = 8 hrs = 28800 s To find : Amount of water pumped

Q: Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building…

A: Pump Pump is a mechanical device which is used to lift the water from lower elevation to higher…

Q: As per common design practice, the three types of hydraulic turbines, in descending order of flow…

A: Given ; Hydraulic turbine is a rotary machine that converts kinetic energy and potential energy of…

Q: Two pipes, one circular and one square have the same cross-sectional area. Which has the larger…

A: Given              Radius = R  Side of square = a Find Larger hydraulic radius

Q: Constant operating speed characteristics; H = 55- 460V2 and ng = 8,2v – 130V3 %3D Water is drawn…

A:

Q: A Francis turbine is to be designed to produce 27 MW at a shaft speed of 94 rev/min under an…

A:

Q: In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.6 m3/s…

A:

Q: How does the Venturi Meter's manometer reading affect its discharge?   How does a Venturi Meter…

A:

Q: A proposed hydroelectric plant is to have a flow of 200 cfs against a net head of 30 ft. The…

A: Specific Speed (Ns): it is the speed of a turbine at which it would produce unit power when working…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A: Given     Gross head, HG = 25 m          Head loss, h = 5 m          Net head, H = 25 - 5 = 20 m…

Q: During a retrofitting project of a fluid flow system to reduce the pumping power, it is proposed to…

A: From the table 14-4, The loss coefficient for miter elbow with vanes is KL≈0.2 The loss coefficient…

Q: 1. The irrigation pump is used to supply water to the pond at B at a rate of 0.09 m3/s. If the pipe…

A: Given:Q=0.09 m3/sd=150 mmhl=0.1 m/m

Q: Which of the following head is neglected in ideal Bernoulli's Energy equation O 1. Potential head O…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.