A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is h 5 0.5 in., its length is L 5 30 in., and its thickness is t 5 0.5 in. Shear force of V 5 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.

A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is h 5 0.5 in., its length is L 5 30 in., and its thickness is t 5 0.5 in. Shear force of V 5 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. and a modulus of elasticity ??? = 10,000 ??? and ?????? = 29,000 ???. The allowable stress of aluminum is 7.8 ksi and steel is 1.7 ksi. If the bar initially vertical,a. Determine the maximum P that can be applied.b. Determine the deformation of steel.c. Determine the deformation of aluminum.
Before the 400 kN load is applied, the rigid platform rests on two steel bara, each of cross sectional area 1400mm^2, as shown in the figure. The cross sectional area of the aluminum bar is 2800 mm^2, Use E=200 GPa for steel and E = 70 GPa for aluminum. NEGLECT the weight of the platform A.) Compute the stress in the aluminum bar in Mpa after the 400 kN load is applied Choices: 45.64,16.30,40.62,14.51 B.) Compute the stress in the steel bar in Mpa Choices: 68.03,95.24,128.35,126.56 C.) Compute the shortening of the steel bar in mm. Choices: 0.125,0.085,0.113,0.158
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
A closed right circular cylinder has radius 4 units and height 18 units A load of an unknown weight is put on top of the cylinder, causing the cylinder to shorten by 2.1 units. Find the new volume of cylinder due to this deformation in the height of the cylinder.
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.
A steel rail for railroad track is 10 m long. Determine the stress in the rail if it was completely restrained from expanding. Let E = 210 GPa and =12 x 10-61/ C. The temperature changes from 20 C to 35 C. A)37.8 MPa B)18.9 MPa C)23.8 MPa D)46.4 MPa
A steel rod of length = 3m, diameter - 300 mm and modulus of elasticity = 200 GPa is inserted into an aluminum tube. The aluminum tube as length = 2999.95 mm, wall thickness of 20 mm and modulus of elasticity of 70 GPa. a.) Determine the deformation of each member due to axial compressive force P-100 KN. b.) Determine the stress in each member. c.) Determine the axial strain if no gap exists. WITH FULL SOLUTION ASAP PLEASE
Rigid bar ABC is supported by member (1), which has a cross-sectional area of 0.6 in.2, an elastic modulus of E = 10000 ksi, and a coefficient of thermal expansion of α = 12.1 × 10−6 /°F. Assume that a = 95 in., b = 40 in., and c = 135 in. After load P is applied to the rigid bar and the temperature rises 80°F, a strain gage affixed to member (1) measures a strain increase of 2902 με. Determine the magnitude of applied load P. Note: Assume the strain measuring system does not automatically compensate for temperature changes.
1. calculate the depth of neutral axis (mm) of the beam section from the top. a. 60 b. 70 c.80 d. 90 2. calculate the moment of inertial of the section about the neutral axis in x10^6 mm^4. e. 15.52 f. 12.75 g. 15.63 h. 9.86 3. what is the maximum safe value of P in kN so that the maximum shear stress in the glue will not exceed its working stress of 6 MPa? i. 13.68 j.8.21 k. 10.26 l. 6.84 4. what is the maximum safe value of P in kN so that the shear stress in the glue will not exceed its working stress of 8 MPa? m/ 6.46 n. 12.93 o. 21.55 p. 17.24 5. what is the maximum safe value of P in kn so that maximum bgending stress will not exceed its working stress of 24 MPa in tension under negative bending? q. 5.21 r. 3.39 s. 6.78 t. 2.66 6. what is the maximum safe value of P in kN so that the maximum bending stress will not exceed its working stress of 24 MPa in tension under positive bending? u. 5.32 v. 3.39 w. 6.78 x. 2.66
A 1 meter long steel rod AB of 15-mm diameter is held snugly (without any initial stresses) between rigid walls by the arrangement shown in the figure. (STEEL ROD : E = 200 GPa , α= 12 x 10-6/°C , and yield strength σY = 250 MPa.) a) If the rod undergoes a temperature drop of 24°C, and the bolt at B is tightened causing the rod to elongate by 0.0566 mm, determine the bearing stress between the washer and the wall. b) Determine the amount of temperature drop that is allowed if the factor of safety against yieldingis 4.
line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 200 C under a 50 N pull supported at both ends. During measurement, the ttemperature is 50C and the tape is suspended under a 75 N pull. The line is measured on a 3% grade. Modulus of elasticity of the tape is 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.000016 m/0C. a. Compute the actual length of the tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance.