A lab pair’s Beer’s Law calibration graph 0.08 < A < 0.79 had a best-fit line of A = 0.013 C – 0.023. Data was: off-scale for both the stock solution and solution #1 (10.00 mL stock diluted to 25.00 mL); solution #2 (1.00 mL stock diluted to 25.00 mL) had A = 0.85, and solution #3 (1.00 mL of solution #1 diluted to 25.00 mL) had A = 0.73. What are the concentrations of solution #3 and the stock solution?

A lab pair’s Beer’s Law calibration graph 0.08 < A < 0.79 had a best-fit line of A = 0.013 C – 0.023. Data was: off-scale for both the stock solution and solution #1 (10.00 mL stock diluted to 25.00 mL); solution #2 (1.00 mL stock diluted to 25.00 mL) had A = 0.85, and solution #3 (1.00 mL of solution #1 diluted to 25.00 mL) had A = 0.73. What are the concentrations of solution #3 and the stock solution?

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter14: Chromatography

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

4.Consider the peaks for pentafluorobenzene and benzene in the gas chromatogram shown here. The elution time for unretained solute is 1.06 min. The open tubular column is 30.0 m in length and 0.530 mm in diameter, with a layer of stationary phase 3.0 μm thick on the inner wall. a) Measruing the width, w, at the baseline on the chromatogram, find the number of plates for these two compounds b) Use your answer to (a) to find the resolution between the two peaks c) Using the number of plates N=sqrtN1*N2 with the values from (a) calcuate what the resolution should be and compare your answer with the measured resolution in b
A scientist wishes to measure the concentration of methyl benzoate in a plant stream by gas chromatography. He prepares a sample of butyl benzoate to use as an internal standard. The results of a preliminary run, which used a solution known to contain 1.37 mg/mL of methyl benzoate (peak A) and 1.51 mg/mL of butyl benzoate (peak B), are shown. The area of peak A is determined to be 3.40×102 and the area of peak B is determined to be 398 measured in arbitrary units by the computer. To measure the sample, 1.00 mL of a standard sample of butyl benzoate containing 2.49 mg/mL is mixed with 1.00 mL of the plant stream material. Analysis of the mixture gave a peak area of 437 for peak A and 415 for peak B. What is the concentration of methyl benzoate in the plant stream?
25 ml of pickled brine was taken from an apple pickled with vinegar and diluted to 500 ml, 25 ml of this was taken and acidity was determined with 0.2 N (Factor: 1.05) NaOH. In the main trials, 6.3 ml - 6.5 ml - 6.9 ml, respectively, 0.1 ml base was used in the analysis without using the sample.For example, how many ppm is its acidity?
In a GC run, dodecane was used as test solute for a 30 m x 250 ?m i.d. DB-5 column. The dodecane peak eluted at 5.2 min. and the distance between its two inflection points was 4.0 s. This was the number of theoretical plates generated by this column:
The concentration of purified OXA-M290 is tested with a BCA assay. Serial dilutions of a bovine serum albumin (BSA) stock solution are prepared, then pipetted into a 96-well plate; each dilution of the BSA standard is tested in triplicate. Then, bicinchoninic acid and Cu2+ ions are added to all of the wells of the plate. After incubating the plate for 1 hour, a microplate reader is used to measure the absorbance of all of the wells in the plate at 560 nm. This generates the following data: BSA conc. (μg/mL), Replicate 1 Absorbance, Replicate 2 Absorbance, Replicate 3 Absorbance 40, 1.360, 1.403, 1.481 20, 0.750, 0.745, 0.810 10, 0.380, 0.344, 0.398 5, 0.198, 0.160, 0.183 2.5, 0.090, 0.100, 0.085 1.25, 0.038, 0.043, 0.051 0.625, 0.024, 0.028, 0.019 Prepare a calibration curve using these data. You can use Excel, R, SPSS or an equivalent graphing software. In this graph, plot absorbance (y-axis) against the concentration of the protein standard (x-axis). Calculate and plot…
In a chromatography experiment, a solution containing 0.083 7 M X and 0.066 6 M S gave peak areas of AX = 423 and AS 5 347. (Areas are measured in arbitrary units by the instrument.) To analyze the unknown, 10.0 mL of 0.146 M S were added to 10.0 mL of unknown, and the mixture was diluted to 25.0 mL in a volumetric flask. This mixture gave the chromatogram in Figure 5-8, with peak areas AX = 553 and AS = 582. Find the concentration of X in the unknown.
Chemistry The levels of an organic pollutant (P) in the groundwater at the perimeter of a plant were a cause for concern. A 10 mL sample of the water was taken and the pollutant was extracted with 95% efficiency using 25 mL of diethyl ether. GC was used to analyse the concentration of P in diethyl ether. A calibration curve was plotted for a series of standards of P which yielded the following results: Peak Area Toluene Conc. (µg/ml) 12,000 2.6 23,700 5.0 35,500 7.7 46,800 9.9 31,250 Sample Determine the concentration of P in ppb in the initial groundwater sample.
Two salts A and B are dissolved in water. At the temperature of the experiment, the solubility of A is 1 kg A/kg pure water and that of B is 0.4 kg /kg water. It will be assumed that the solubilities of the two salts are not affected by the presence of each other. If originally 20 kg of A and 20 kg B are dissolved in 100 kg water, and some of the water is evaporated from solution, calculate the: (1) amount evaporated (2) weight of mother liquor (3) composition of mother liquor (4) weight of each crystal formed for the following cases: a) 50% of the water is evaporated b) Enough water is evaporated to reduce the total weight of the solution to 50% of the original value c) Enough water is evaporated to leave the solution saturated with A, without crystallizing any A d) Enough water is evaporated so that the remaining solution is 50% of the original value.
An analyst determines the Cl^- content of rain water with ion chromatography. The data for the calibration line in the range 5 to 50 milli equivalents per liter (mEq/L) is shown in the table below. Additionally, a blank sample was analysed 5 times and the following results obtained: 1.1, 0.5, 0.1, 0.9 and 1.2 ppm Ct Calculate the detection limit (DL) for the method with a 98.3% confidence level. Use ALL data and show equations
Louie performed paper chromatography to identify which among the four availablereference mixtures — WAR, OFF, YIN, MEW — have the same components as hisunknown sample, GUN. He spotted the standards and the sample in a Whatman No. 1filter paper, which he placed in a developing chamber containing 3% KCl. After 20minutes, Louie obtained the chromatogram below, immediately noting that the distancetravelled by the solvent from the origin is 79.0 mm. On the other hand, the distances (incm) traveled by the developed spots were tabulated as follows.(see attached) Questions: 1. Is the type of paper chromatography performed normal or reversed? Why?2. Calculate the Rf of the spots from the samples. Report your answers in four decimal places.
1-3: A stock solution of 70% v/v ethanol was diluted with distilled water to prepare 1L of 21% v/v ethanol. (Density of ethanol = 0.789 g/mL; MW of ethanol = 46 g/mol) 1. Determine the initial volume of 70% v/v ethanol used in the preparation. 2. How much water was added to the stock solution to make 1L of the final concentration? 3. The molarity of 5.0 mL of 70% v/v ethanol was found to be __________. 4-6: A solution contains 45.0 g of methanol, CH3OH, dissolved in sufficient water to give a total mass of 210.6 g. 4. Compute for the number of moles of the solute present in the given solution. 5. What is the mass (in kg) of water used to dissolve the solute from the given problem? 6. Determine the molal concentration of the said solution.
(i) An unknown sample (0.100 g dissolved in 100 mL ethanol) was then analysed by GC, among a number of otherpeaks, there was one at 9.5 min with integration 1250. Discuss how this could be quickly confirmed as being due to A. (ii) An aliquot (1 mL) of a solution of B (0.100 g dissolved in 100 mL ethanol) was added to the unknown sample. Now in addition to the peak at 9.5 min (integration 1250) there was a peak at 11.5 (integration 1000). Determine how much A was in the unknown sample.