A manual chain hoist is a machine used to lift a 125 kg crate. A force of 200 N is applied to the effort chain through a distance of 3m, and the crate is lifted a distance of 0.4m. What is the Mechanical Advantage provided by the chain hoist?

A manual chain hoist is a machine used to lift a 125 kg crate. A force of 200 N is applied to the effort chain through a distance of 3m, and the crate is lifted a distance of 0.4m. What is the Mechanical Advantage provided by the chain hoist?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Related questions

Q: A dual pulley with an inner diameter of 100 cm and an outer diameter of 300 cm supports a pair of…

Q: A 2.0m long bar is being used as a first-class lever. It has a load of 720 N placed on one end…

Q: Calculate the effort (F) that has to be applied in the pulley system 100 kg 981 N 245.25 N 327 N…

Q: Two farmers are pushing on a gate with forces FA and FB, applied at locations A and B respectively.…

Q: A factory worker is pushing a large box of cookies across a level horizontal portion of the factory…

Q: Q1. In the operation of a screw jack, which has a velocity ratio of 112, an effort of 30 N raises a…

Q: Below is a diagram of a human arm. 5.0 cm F, M -15 cm- -35 cm- W. B The forearm is lifted by the…

Q: (b) A weight, as shown in figure Qlb-(a) has to move at constant velocity of 2 m/s on an inclined…

A: Let F1 =force applied in horizontal direction N=Normal reaction on inclined plane f=friction…

Q: Figure 1 shows an over-head view (pandangan dari atas) of three horizontal forces acting on a wooden…

Q: Spiderman, whose mass is 75.0 kg, is dangling on the free end of a L = 11.5-m-long rope, the other…

A: Given, Mass of Spiderman m = 75 kg Length of rope L = 11.5 m θ = 59.3o

Q: As shown, a frictionless pulley hangs from a system of springs and a cable. The pulley is…

Q: wo weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 lb…

Q: A pair of pliers grips the bolt as shown below. 30 mm X₁ B 70 mm X₂ Note: tan 0=y₁/x₂ (a) For the…

A: (a) Draw the free-body diagram of each parts of the pair of pliers.

Q: A lever 5 m long, has its fulcrum a distance of 0.50 from its end where a weight is to be lifted. If…

Q: To get up on the roof, a person (mass 66.7 kg) places an aluminum ladder (mass 9.30 kg) against the…

A: Given, The mass of the person, mP=66.7 kg The mass of the ladder, mL=9.3 kg All the given dimensions…

Q: A weightlifter raises a 150-kg barbell from the floor to a height of 2.2 m in 0.80 s. What is his…

Q: lever is used to lift a heavy load. When a 25 N force pushes one end of the lever down 1.8 m, the…

Q: In a hydraulic press, the small cylinder has the diameter of 8 cm while the larger piston has the…

A: Given Data The diameter of the smaller piston is: d=8 cm The diameter of the larger piston is: D=22…

Q: A piano mover rolls a 200 kg piano at constant speed up a ramp 2m long at an angle of 30 degrees…

A: Given, Mass of the piano , M = 200kg. Length of the inclined , L = 2m. Angle of inclination = 30…

Q: Trina is a gym goer with a leg length of 84 cm. Suppose that she is in the gym doing straight leg…

Q: The energy required to punch a hole 3.20 kJ from a flywheel mean diameter of 850 mm that slows down…

Q: 1. (a) You have to lift a load of 500 N. Which pulley system will you prefer? Why? Find out the…

A: given: (a) weight of block=500N effort =T balance the force on pulley:2T=500T=250Neffort(T)=250N…

Q: A hydraulic crane has a small piston diameter of 10 mm and a large piston diameter of 8 cm. After…

Q: A 100 ft cable weighing 5 lb / ft supports a safe weighing 500 lb. Find the work done in winding 80…

Q: Fig. 3.19 shows a hammer of mass 6 kg and pivoted at A. It falls against a wedge of mass 1 kg which…

Q: A body of weight 500 N is lying on a rough horizontal plane having coefficient of friction 0.3. Find…

A: Given, W= 500 N μ=0.3

Q: 6. A painter whose mass is m holds himself up while sitting on the modified bosun's chair assembly…

Q: An object of weight 250 N is initially stationary on a 35° inclined plane. What time will the object…

Q: *** A force of 75N is applied to a nutcracker to crack open a walnut. If the MA of the nutcracker is…

A: Given:Finput=75 NM.A.=5

Q: A pulley and rope arrangement is shown below 40 kg (Hold by a person) If coefficient of friction…

Q: 1. A body of mass 5 kg rests on a horizontal surface and the coefficient of friction between the two…

Q: A 1380 kg block is being pulled across the floor by a rope which is wrapped around a motorized…

A: From the given data,

Q: Billy Bob is trying to decide whether to push a 50 kg dresser up a 4.5 m ramp or lift it directly…

A: We can answer up to 3 subpart so we will answer first 3. Please resubmit the question by specifying…

Q: .A flywheel rim which weighs 822 pounds has a mean diameter of 44 inches. The speed is to be…

Q: To find the Mechanical Advantage of ANY simple machine when given the force, use MA = R/E. 1. An…

A: Given: The value of force applied by the screwdriver is, R=90 N. The value of effort force is, E=30…

Q: A rope 17 cm is suspended between two hooks, 13 cm apart and at the same level. What is the pull on…

Q: A 490-kg block is resting on a 53 deg inclined plane with a coefficient of friction = 0.44. Find the…

Q: Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m length. The maximum…

A: Given Data The mass of the belt is: m=0.9 kg/m The maximum tension is: T=2.2 kN The angle of the…

Q: 1.) Assume that some ancient civilization built their monuments with a compound system of simple…

A: Two compound pulleys are given with efficiency e1 = 0.8 and e2 = 0.7 efficiecny of slope, e0 = 0.9…

Q: A block is constantly moving horizontally due to a horizontal force of 50kn. It is given that the…

A: Answer is given below:

Q: The small piston of a hydraulic press has a cross-sectional area of 3cm2, and its larger piston has…

A: Given data: The cross sectional area of small piston, A1 = 3 cm2. The cross sectional area of large…

Q: Use the results of your lever apparatus tests to explain the relationship between mechanical…

A: Mechanical advantage is defined as the ratio of output force or force lifted by the lever to the…

Q: ... Hamstring 20cm Weight of lower leg + foot =4.5kg The weight of the lower leg and foot combined…

A: Find the value of force in the hamstring

Q: A gardener uses a 60-N wheelbarrow to transport a 250-N bag of fertilizer.What force must she exert…

A: Given The weight of wheelbarrow is W1=60 N. The weight of bag of fertilizer is W2=250 N. Consider…

Q: A hydraulic press has a ram of 30 cm diameter and a plunger of 2cm diameter. it is used for lifting…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: 1. A bus model with 5kg mass being pulled horizontally against a friction force of 0.5N. Draw the…

Q: An inclined plane at an angle of 15o is used to lift a 250 kg sofa through a vertical height of 5…

A: Drawing the diagram for the given question,

Q: The forearm shown below is positioned at an angle θ with respect to the upper arm, and a 5.0-kg mass…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A manual chain hoist is a machine used to lift a 125 kg crate. A force of 200 N is applied to the effort chain through a distance of 3m, and the crate is lifted a distance of 0.4m. What is the Mechanical Advantage provided by the chain hoist?

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An inclined plane at an angle of 15o is used to lift a 250 kg sofa through a vertical height of 5 meters. If the coefficient of kinetic friction is 0.12, what is the Mechanical Advantage, Ideal Mechanical Advantage, and efficiency of the plane?
A lever with a mechanical advantage of 6 is attached to the pump piston of a hydraulic press. The area of the pump piston is 1.2 in2 and that of the output piston is 18 in2. A) If the press is 75% efficient, find the force the output piston exerts when a force of 30 lbs is applied to the pump lever.
A 1380 kg block is being pulled across the floor by a rope which is wrapped around a motorized winch. The coefficient of kinetic friction between the block and the floor is 0.41, and the block moves at a constant speed of 1.34 m/s.What is the power output of the motor, in Watts (W)?Calculate the total work done by the winch if the box moves a total of 4.50 meters. Give your answer in Joules (J).
A body of mass 5 kg rests on a horizontal surface and the coefficient of friction between the two surfaces is 0.44. What is the horizontal force required to make the body moving?
In a simple machine, an effort of 100 Newton lifts a load of 840 Newton. if the distance moved by the effort is 20cm and that by load is 2 cm,find: (i) Mechanical advantage (ii) Velocity ratio (iii) Efficiency (iv) Effort lost in friction (v) friction in terms of load
A hydraulic crane has a small piston diameter of 10 mm and a large piston diameter of 8 cm. After the point of impact of the direct force from the axis of the mechanical crane is 24 mm, while the point of impact of the indirect force from the axis of the mechanical winch was 6.4 cm. It was used to lift a load of 18 tons. Required: 1- Draw a diagram For the crane 2- hydraulic advantage 3- mechanical benefit 4- direct force 5- external force 6- general mechanical benefit 7- if the load increases by 30% calculate the direct force and external force in this case 8- Calculate the diameters of the crane necessary to lift a load of 15 tons With the same external force as the original, noting that the maximum diameter of the small piston is not more than 18 mm.
In a belt arrangement two pulleys are connected by flat belts having same diameters. Themaximum force on the tight side of belt is 662 N. If co-efficient of friction is 0.3 thenwhat is maximum force on the slack side of the belts?
A 11120 N car is designed with a 310 cm wheelbase. The center of gravity is located 60 cm above the pavement and 105 cm behind the front axle. If the coefficient of road adhesion is 0.6, what is the maximum tractive effort that can be developed if the car is (a) front-wheel drive and (b) rear-wheel drive? (c) how far back from the front axle would the center of gravity have to be to ensure that the maximum tractive effort developed for front- and rear-wheel drive options is equal?
The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
Two weights are hung over two frictionless pulleys that are connected by a wire rope to a 500 Ib horizontal block that are in between and below them. The wire rope attached to the upper left end of the block and to the left pulley is at 45 degrees with the horizontal and the wire rope that connects the upper right end of the block to the right pulley is at 30 degrees with the horizontal. If the weight on the left pulley is 50 lb, fs= 0.30 and fk = 0.20 on the surface of block what weight W on the right pulley will cause the 500 lb block to just start moving to the right? *
A 30g wood block is firmly attached to a horizontal spring. The coefficient of friction between the block and the floor is 0.4. A force of 20N compresses the spring 20cm and then released. a. What is the spring constant? b. How far beyond the equilibrium position will it stretch on the first swing? c. How many seconds will it take the block to return to its initial position?
6.4. A force of 300 N is sufficient to keep a 100-kg wooden crate moving at constant velocity across a wooden floor. What is the coefficient of kinetic friction?