A moonshiner makes the error of filling a glass jar to the brim and capping it tightly. The moonshine expands more than the glass when it warms up, in such a way that the volume increases by 0.4% (that is, ΔV/V0 = 4 ✕ 10-3) relative to the space available. Calculate the force exerted by the moonshine per square centimeter if the bulk modulus is 1.8 ✕ 109 N/m2, assuming the jar does not brea

Q: A shaft having length equal to 10 m and diameter equal to (50 + 21) mm is simply supported at both…

A:

Q: A child slides across a floor in a pair of rubber-soled shoes. The frictional force acting on each…

A: NOTE: As per bartleby guidelines we can answer only first question. For remaining questions please…

Q: 2.0-m-long, 1.0-mm-diameter wire is suspended from the ceiling. Hanging a 4.5 kg mass from the wire…

A:

Q: A load with a weight of 125.0Newtons is attached to a brass wire with a length of 7.5 meters.…

A: GIVEN   F=125N l= 7.5 m Y=8.96 X 10^11 Pa r=0.7 X  10^3 m

Q: After a fall, a 95 kg rock climber finds himself dangling from the end of a rope that had been 15 m…

A: Given:  mass, m = 95 kg  length of rope, L = 15 m  diameter of rope , d = 9.6 mm  extension in…

Q: Two wires are made of the same material, their Young’s Modulus constant is 10 x10^10 Pa. Wire X is 4…

A: Given: Two wires are X & Y. Young's modulus constant, γ=10×1010 Pa Considered wire Y length be…

Q: You have a 15 cm^3 block of copper that you wish to make into a cylindrical wire. If the Young's…

A: stiffness of wire is given by, k=A ELwhere V=ALA=VLNow,k=VEL2

Q: A tensile stress is to applied along the long axis of a cylindrical brass rod that has a diameter of…

A:

Q: A ball has a radius of 1 meter. The Bulk modulus is 4.2 × 1010 N/m2. It is located on the surface of…

A:

Q: A small, spherical bead of mass 3.00 g is released from rest at t = 0 from a point under the surface…

A: Mass of  the bead m=3g                               m=3×10-3 kg  Terminal Speed    vt= 2 cm/s =…

Q: A wire of uniform cross sectional area of 0.45 mm is stretched at both ends by a total force of 7O N…

A: Given: Area of cross section of wire is 0.45 mm2. Force acting on the wire is 70 N. Strain produced…

Q: An aluminum (ρ = 2.7 g/cm3) wire is suspended from the ceiling and hangs vertically. How long must…

A:

Q: Calculate the volumetric change in a copper cube of side length (40mm) when subjected to a pressure…

A: Length of the copper cube is L = 40 mm = 40×10-3 m Pressure applied, P=20 MPa = 20×106 Pa Modulus of…

Q: A load with a weight of 125.0Newtons is attached to a brass wire with a length of 7.5 meters.…

A: Y= Young's modulus = stress/strain Stress = force /area of cross section Stress = F/a Strain =…

Q: When a 125-kg piece of equipment is hung from a steel wire of diameter 6.00 mm, it stretches the…

A:

Q: A wire of uniform cross sectional area of 0.15 mm2 is stretched at both ends by a total force of 40…

A: Given, Area of cross section of the wire A = 0.15 mm2 Total force acting on the both end F = 40 N…

Q: What is the force required to a steel wire to double its length when its area of cross-section is…

A: In the question it is given that ,Young's Modulus Y=200GPa=200×106Pa=2×104N/m2length of the wire…

Q: A 20 kg chandelieris suspended from the ceiling by four vertical steel wires. Each wire has an…

A:

Q: A cylindrical specimen of a titanium alloy having an elastic modulus of 108 GPa and an original…

A:

Q: A steel wire, 3.2 m long, has a diameter of 1.2 mm. The wire stretches 1.6 mm when it bears a load.…

A:

Q: After a fall, a 73 kg rock climber finds himself dangling from the end of a rope that had been 17 m…

A: This problem requires following formula to be used. a)Strain is ratio of stretched length to…

Q: A large 75-kg lighting fixture can be hung from wires of identical size and shape made of aluminum,…

A: Given: The mass is 75 kg. The Young's modulus of aluminum is 0.70x1011 Pa. The Young's modulus of…

Q: After a fall, a 86 kg rock climber finds himself dangling from the end of a rope that had been 16 m…

A:

Q: For the connection shown, the average shear stress in the 19-mm-diameter bolts must be limited to…

A:

Q: The pressure increases by 1.0 x 104 N/m2 for every meter of depth beneath the surface of the ocean.…

A: Given: The increase in pressure is 1.0×104 N/m2 per meter. The bulk modulus of Pyrex is 2.6×1010…

Q: A spider of mass 6.3  10-4 kg hangs from a 70.9 cm long thread whose diameter is 2.0  10-3 mm.…

A:

Q: After a fall, a 80 kg rock climber finds himself dangling from the end of a rope that had been 14m…

A:

Q: 12 kN (1) !D A B 1.5 m-1.5 m -1.5 m-

A:

Q: A load with a weight of 125.0Newtons is attached to a brass wire with a length of 7.5 meters.…

A:

Q: A piano wire 0.82 m long and 0.93 mm in diameter is fixedon one end. The other end is wrapped around…

A: The expression for the cross-sectional area is A=π4d2=π40.93 mm×1 m1000 mm2=6.7929×10-7 m2 When the…

Q: Two wires are made of the same material, their Young’s Modulus constant is 10 x10^10 Pa. Wire X is 5…

A:

Q: A wire of 0.5 mm cross-section diameter nd 120 cm length is suspended vertically. What is the…

A: Write the given value of this problem: Diameter of wire(d)=0.5 mm or 0.5×10-3mLength of wire(L)=120…

Q: A cube with edges exactly 3.00 cm long is made of material with a bulk modulus of 7.00 x 10 9 N/m 2.…

A: Given: Length of cube’s side (a) = 3.0 cm. = 3.0×10-2 m. Bulk modulus (B) = 7.0×109 N/m2. Pressure…

Q: A bar of an advanced alloy having an elastic modulus of 107 GPa and an original diameter of 3.8 mm…

A:

Q: A 3m long steel bar whose diameter is 25 mm is compressed by a 25 KN force. If the value of the…

A: The stress is defined as the force per unit area.

Q: A metallic cube of side 125cm is subjected to a uniform force acting normal to the whole surface of…

A:

Q: A hydraulic press contains 0.25 m3 of oil. Find the decrease in the volume of the oil when it is…

A: Let the Bulk modulus of oil is given by B. Let the change in pressure is given by ∆p. Let the change…

Q: You hang a heavy ball with a mass of 40 kg from a silver rod 2.8 m long by 2.2 mm by 2.7 mm. You…

A: The ratio of distance to time taken to travel a distance is used to calculate speed. Because it has…

Q: Calculate the Young's modulus for the given wire when a load of 2000 N is hung from the wire? The…

A: The Young's modulus is given by  Y = F LA l where, F is the force, L is the original length, A is…

Q: A moonshiner makes the error of filling a glass jar to the brim and capping it tightly. The…

A: Given: ΔV/V0 = 5 ✕ 10-3 Bulk modulus = 1.9 × 109 N/m2 Find The force exerted by the moonshine per…

Q: A copper wire of length 3-m and 1-mm diameter is subjected to a tension of 5-N. Calculate the…

A: Given: The length of the wire is 3 m. The diameter of the wire is 1 mm. The tenson in the wire is 5…

Q: In her gymnastic routine, Regina dismounts from the uneven-parallel bars and lands straight-legged…

A:

Q: A steel rectangular block, a = 2.4cm wide and b =1.2 cm deep, is subjected to an axial tensile load…

A: Modulus of elasticity for a volume object is known as Bulk modulus of elasticity.

Q: Masses M1 and M2 are supported by wires that have equal lengths when unstretched. The wire…

A: masses M1 and M2 Aluminium wire                                           steel wirediameter,d1=1.35…

Q: After a fall, a 94 kg rock climber finds himself dangling from the end of a rope that had been 18 m…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).