A picture is taken of a pole vaulter, and the minimum radius of curvature of the pole is estimated to be 5 m. If the pole is 45 mm in diameter and it is made of a glass-reinforced plastic for which E = 131 GPa, determine: a) The maximum strain in the pole. b) The maximum tensile stress in the pole. c) The maximum compressive stress in the pole.

A picture is taken of a pole vaulter, and the minimum radius of curvature of the pole is estimated to be 5 m. If the pole is 45 mm in diameter and it is made of a glass-reinforced plastic for which E = 131 GPa, determine: a) The maximum strain in the pole. b) The maximum tensile stress in the pole. c) The maximum compressive stress in the pole.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.6P: A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of...

See similar textbooks

Similar questions

A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
When subjected to a compressive load, the length of the rod is 199,6 mm, and its diameter is 10 mm. If the original length was 200 mm, and modulus is 70 GPa, determine: 1.1 The stress and strain in the rod when loaded. 1.2 The magnitude of the load.
Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10^6 psi. AB =4 ft BC =4.5 ft, CD = 3.5 ft. Note: Final Answer in 4 decimal places.
Question 3 3. A string 4 mm in diameter has original length 2 m. A force of 200 N. pulls the string. If the final length of the spring is 2.02 m, determine: (a) stress (b) strain (c) Young's modulus.
A sign of mass 2,500-Kg hangs from the bottom end of a vertical cylindrical aluminum bar (with a diameter of 12-cm). (a) What is the stress within the bar? (b) What is the bar’s strain? (c) If the bar is 10-m long, how much is it lengthened?
Question # 1 Fig 2 shows an unstressed aluminum plate 2/4 inches thick. A circle of 9.5 inches diameter is scribed on it. Normal stresses of 15 ksi and 22 ksi, along x and y direction, are caused by forces acting in the plane of the plate. For Poisson's ratio 4 and modulus of elasticity 10 *10^6psi,then determine the following (a)change in the length of diameter AB (b)change in diameter CD (c)variation in the plate thickness (d)the volume change of the plate
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly to the end. The diameter and the length of the steel rod are given as 10 mm and 120 mm,respectively, the diameter and the length of the brass rod as 20 mm and 80 mm respectively. The rod is used as a tie in a link mechanism and the strain in the brass rod is limited to 0,00053. Given that the total extension of the composite rod must not exceed 0,1624 mm and E for steel is 200 GPa, respectively. Determine : A) Strain in the steel rod B) Load carried by the steel and brass rods C) Modulus of elasticity for the brass
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains. PLEASE ANSWER I,G,H
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 mis under tension. If the wire length extension is 2.5 mm, calculate the stress in thewire. Give your answer in N/m2to 2 decimal places.
A hollow circular pole 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is subjected to a torque and a lateral force at the free end. Given: Torque, T = 25 kN-m Lateral Force, N = 3 kN Shear Modulus of Elasticity = 78 GPa Allowable Shear Stress = 60 MPa 1. What is the maximum shear stress (MPa) at the outside surface of the pole due to the torque, T? 2. What is the angle of twist (degree) due to the torque? 3. Find the maximum flexural stress (MPa) at the base of the pole due to the lateral force.