A piece of beef steak 5 cm thick will be frozen in the freezer room -25 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 10 W / (m² K). t f = Answer hour.

A piece of beef steak 5 cm thick will be frozen in the freezer room -25 ° C. This product has a moisture content of 73%, a density of 970 kg / m³, and a thermal conductivity (frozen) of 1.1 W / (m K). Estimate the freezing time. using the Plank equation. This product has an initial freezing temperature of -1.75 ° C, and the movement of air in the freezing room gives a convective heat transfer coefficient of 10 W / (m² K). t f = Answer hour.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.13P

See similar textbooks

Similar questions

3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
1.15 A thermocouple (0.8-mm-diameter wire) used to measure the temperature of the quiescent gas in a furnace gives a reading of . It is known, however, that the rate of radiant heat flow per meter length from the hotter furnace walls to the thermocouple wire is 1.1 W/m and the convection heat transfer coefficient between the wire and the gas is K. With this information, estimate the true gas temperature. State your assumptions and indicate the equations used.
A food product with 80% moisture content in a 7 cm diameter can wants to be frozen. product density is 1000 kg / m³ thermal conductivity is 1.0 W / (m K) and initial freezing temperature is -2.25 degrees Celsius after 8 hours in freezing medium -35 degrees Celsius Temperature to -10 degrees Celsius estimate convection heat transfer coefficient freezing medium assume the can as an infinite cylinder h =
A food product with 80% moisture content in a 5 cm diameter can wants to be frozen. The density of the product is 1000 kg / m cubic, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -1.75 ° C. After 10 hours in -25 ° C freezing medium, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder
A 5 cm thick beef steak is being frozen in a -35°C room. The product has 73% moisture content, density of 970 kg/m³, and thermal conductivity (frozen) of 1.1 W/(m K). Estimate the freezing time using Plank’s equation. The product has an initial freezing temperature of -1.75°C, and the movement of air in the freezing room provides a convective heat-transfer coefficient of 10 W/(m² K) a. tf = ... hour
A food product with 80% moisture content in a 10 cm diameter can wants to be frozen. The density of the product is 1000 kg / m³, the thermal conductivity is 1.0 W / (m K), and the initial freezing temperature is -2 ° C. After 14 hours in the freezing medium -30 ° C, the product temperature becomes -10 ° C. Estimate the convection heat transfer coefficient of the freezing medium. Assume the can as an infinite cylinder.
A food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at a temperature of -35 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 1 cm, and a density of 980 kg / m³. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 50 W / (m² K). Calculate the freeze time. t f = hour
A food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at a temperature of -35 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 1 cm, and a density of 980 kg / m³. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 40 W / (m² K). Calculate the freeze time. t f = Answer hour.
A food product wants to be produced in a small round shape (pellet) by freezing it in a water blast freezer freezer. Air freezer operates at a temperature of -35 ° C. The initial product temperature is 25 ° C. The pellet has a diameter of 1.2 cm, and a density of 980 kg / m³. The initial freezing temperature is -2.5 ° C. The latent heat of freezing of the product is 280 kJ / kg. The thermal conductivity of the frozen product is 1.9 W / (m ° C). The convective heat transfer coefficient is 40 W / (m² K). Calculate the freeze time. t f = Answerhour.