A plate (0.5 m * 0.5 m) is inclined at an angle of 30°. The top surface of the plate is well insulated. Estimate the rate of heat loss from the plate when the bottom surface is maintained at 60°C and the surrounding atmospheric quiescent air is at 0°C.

A plate (0.5 m * 0.5 m) is inclined at an angle of 30°. The top surface of the plate is well insulated. Estimate the rate of heat loss from the plate when the bottom surface is maintained at 60°C and the surrounding atmospheric quiescent air is at 0°C.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.4P: An electrical transmission line of 1.2-cm diameter carries a current of 200 amps and has a...

See similar textbooks

Related questions

Q: For a natural convection from the vertical plates, if Rayleigh number is given as 1 × 101º then the…

A: Given, Rayleight number = Ra = 1 x 1010 For 109 < Ra < 1012, nusselt number (Nu) can be…

Q: A black 20-by-20-cm plate has air forced over it at a velocity of 2 m/s and a temperature of 0◦C.…

A: Given: The area of plate, A = 20x20 cm The velocity of air, v = 2 m/s The temperature of air, Ta =…

Q: What electrical current is required to maintain a 0.076 mm diameter, 0.6 m long vertical wire at…

A: NOTE:- Here, we have to use correlation for find out the convection heat transfer rate.So, answer…

Q: In a production facility, large brass plates of 4-cm thickness that are initially at a uniform…

A: Given data: The thickness of the plate is t=4 cm=0.04 m The initial temperature of plate is…

Q: What are the turbulence intensity differences on offshore and onshore?

A: Turbulence intensity differences on offshore and onshore ;

Q: A 6-mm-diameter electrical transmission line carries an electric current of 50 amperes and has a…

A: Given- parameter given- diameter= 6mm current= 50A resistance= 0.002ohm/mt. length k=218w/m-k

Q: In the laminar flow of air (Pr = 0.7) over a heated plate. if ö and S denote, respectively, the…

Q: A long 10-cm-diameter steam pipe whose external surface temperature is 110°C passes through some…

A: In order to proceed with the problems some assumptions need to be considered. Steady operating…

Q: When does international humanitarian law apply? *

A: International humanitarian law applies only to armed conflict; it does not cover internal tensions…

Q: Q12) Derive an expression for the overall heat transfer coefficient (U) for one layer plane with…

Q: What is the function of the primary flight control surfaces? How about secondary flight control…

Q: Why is heat transfer faster in forced convection compared to natural convection

A: Natural convection: when heat transfer is taking place due to motion of fluid caused by density…

Q: Consider a 50-cm-diameter and 95-cm-long hot water tank. The tank is placed on the roof of a house.…

A: Given data Diameter of the pipe = 50 cm =0.5m Length of the pipe = 95cm = 0.95m Final temperature of…

Q: Q1. A 6-mm-diameter electrical transmission line carries an electric current of 50 A and has a…

A: Given data: The diameter of the electrical transmission is d=6 mm=0.006 m The electric current in…

Q: Consider a sphere and a cylinder of equal volume made of copper. Both the cylinder and sphere 'are…

A: The answer is in next step

Q: Thick fluids such as asphalt and waxes and the pipes in which they flow are often heated in order to…

Q: Consider a hot rectangular plate positioned vertically at constant temperature Ts in quiescent air.…

A: For solution refer below images.

Q: Air is flowing in parallel over the upper surface of a flat plate with a length of 4 m. The first…

A: The value of kinematic viscosity, v = 1.608×10-5 m2s Thermal conductivity, k = 0.02588 Wm·K Prantl…

Q: For external forced convection with an isothermal surface, what is the Nu# correlation equation for…

A: Nusselt number (Nu) signifies the ratio of conductive resistance to the convective resistance…

Q: What electrical current is required to maintain a 0.076 mm diameter, 0.6 m long vertical wire at…

A: Whenever electric current passes through a conductor with resistance heat will be generated. This is…

Q: A 15 mm 3 15 mm silicon chip is mounted such that the edges are flush in a substrate. The chip…

A: Write the properties of air at 50°C. Write the expression of the characteristic length of the…

Q: Determine the total heat transfer rate to the ice water.

A: Given: To determine:the total heat transfer rate to the ice water

Q: Discuss the boundary layer profile that would result for a vertical hot plate, and a vertical cold…

A: Boundary layer of vertical suspended hot plate. Particles of air which contact with plate being hot…

Q: 1] During a plant visit, it was noticed that a 12-m-long section of a 10-cm-diameter steam pipe is…

Q: Q9) Consider a 50 cm diameter and 95 cm long hot water tank. The tank is placed on the roof of a…

Q: The emissivity of galvanized steel sheet, a common roofing material, is ε = 0.13 at temperatures…

A: Write the emissivity of common roofing material. ε=0.13 Write the absorptivity of solar radiation.…

Q: Define the cooling of a boiled egg by forced and natural convection.

A: Rate of heat transfer by convection is given by Where h is convective heat transfer coefficient.…

Q: Consider a hot automotive engine, which can be approximated as a 0.5-m-high, 0.40-m-wide, and…

A: Given data as per question Height of automobile = 0.5m Width of vehicle =0.4 m Length of vehicle=0.8…

Q: Explain, motorcycle engine is either considered as free or forced convection. Justify your answer

A: Motor cycle engine is the 4-stroke petrol engine. Large amount of heat is created from the 2-stroke…

Q: A metallic airfoil of elliptical cross section has a mass of 50 kg, surface area of 12 m2, and a…

Q: Flue gases from an incinerator are released to atmosphere using a stack that is 0.6 m in diameter…

A: Given : The diameter of stack = 0.6 m The height of the stack = 10 m Surface temperature of the…

Q: Determine the thermal boundary layer

A: Given data; A fluid prandi number,Pr=1 Temperature,T=500 KIt is flow over a plate, length,l=2.5…

Q: Consider steady, laminar, two-dimensional flow over a hot plate. Does the convective heat transfer…

A: Given: Consider steady, laminar, two-dimensional flow over a hot plate The wall shear stress is…

Q: A 6-mm-diameter electrical transmission line carries an electric current of 50 A and has a…

A: Given data as per question Current = 50 A Resistance = 0.002 Ω/m Velocity of air = 40 km/hr = 11.11…

Q: 5.0-cm-diameter cylinder is heated to a temperature of 200°C, and air at 30 °C forced across it at a…

Q: Explain, motorcycle engine is either considered as free or forced convection. Justify your answer.

A: Convection is described as a phenomenon in which the alteration of heat takes place by the motion of…

Q: Calculate the convection heat loss from the top and bottom of a flat 1 m square horizontal…

Q: When the convection heat transfer coefficient is very large (h → ∞), the convection resistance…

A: When the convection heat transfer coefficient is very large (h → ∞), the convection resistance…

Q: How is convection caused? Explain with an example?

A: When any fluid is heated, then its lower layer will get heated first, which makes the molecules at…

Q: What electrical current is required to maintain a 0.076 mm diameter, 0.6 m long vertical wire at…

Q: A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in…

A: Given:- Diameter of bottle=10cm height=30cm temp of cold water =3°C temp of air=27°C temp of water…

Question

A plate (0.5 m * 0.5 m) is inclined at an angle of
30°. The top surface of the plate is well insulated. Estimate
the rate of heat loss from the plate when the bottom surface
is maintained at 60°C and the surrounding atmospheric quiescent
air is at 0°C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q6: A large vertical plate 6.1 m high and 1.22 m wide is maintained at a constant temperature of 57+C and exposed to atmospheric air at 4°C. Calculate the heat lost by the plate. Answers: Q=1907 W
How can we use the transient temperature charts when the surface temperature of the geometry is specified instead of the temperature of the surrounding medium and the convection heat transfer coefficient?
An average person generates heat at a rate of 84 W while resting. Assuming one-quarter of this heat is lost from the head and disregarding radiation, determine the average surface temperature of the head when it is not covered and is subjected to winds at 10°C and 25 km/h. The head can be approximated as a 30-cm-diameter sphere. Assume a surface temperature of 15°C for evaluation of ms. Is this a good assumption?
Question No. 3: During a cold winter day, wind at 55 km/h is blowing parallel to a 4-m-high and 10-m-long wall of a house. If the air outside is at 5°C and the surface temperature of the wall is12°C, determine the rate of heat loss from that wall by convection. What would your answer be if the wind velocity was doubled
Consider a person who is trying to keep cool on a hot summer day by turning a fan on and exposing his body to air flow. The air temperature is 32°C, and the fan is blowing air at a velocity of 5 m/s. The surrounding surfaces are at 40°C, and the emissivity of the person can be taken to be 0.9. If the person is doing light work and generating sensible heat at a rate of 90 W, determine the average temperature of the outer surface (skin or clothing) of the person. The average human body can be treated as a 30-cmdiameter cylinder with an exposed surface area of 1.7 m2. Evaluate the air properties at film temperature of 35°C and 1 atm.
What is natural convection? How does it differ from forced convection? What force causes natural convection currents?
What are the turbulence intensity differences on offshore and onshore?
Consider laminar flow of air across a hot circular cylinder. At what point on the cylinder will the heat transfer be highest? What would your answer be if the flow were turbulent?
Consider a 50-cm-diameter and 95-cm-long hot water tank. The tank is placed on the roof of a house. The water inside the tank is heated to 80°C by a flat-plate solar collector during the day. The tank is then exposed to windy air at 18°C with an average velocity of 40 km/h during the night. Estimate the temperature of the tank after a 45-min period. Assume the tank surface to be at the same temperature as the water inside, and the heat transfer coefficient on the top and bottom surfaces to be the same as that on the side surface. Evaluate the air properties at 50°C.
A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a circuit board is cooled by air flowing across it at a velocity of 240 m/min. If the air temperature is 35°C, determine the surface temperature of the component. For air properties evaluations assume a film temperature of 50°C. Is this a good assumption?
What does the friction coefficient represent in flow over a flat plate? How is it related to the drag force acting on the plate?
what is the convection heat transfer coefficient for ambient air at 43°C