Answered: A plate having size 12 by 15 meter is…

A plate having size 12 by 15 meter is pulled with velocity of .08 m/s over a fined plate at a distance of .3 mm with the viscosity of .03N-sec/m2 . Find the Force.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.21P

See similar textbooks

Related questions

Q: A homogeneous block has a mass of 300 kg. The coefficient of friction is 0.45 and the height h is…

Q: Calculate the shear modulus for a given cylindrical metal speciman and test results of T = 1500 N…

Q: A RIGID PLATFORM THAT RESTS ON TWO STEEL BARS SHOWN HAS A NEGLIGIBLE MASS Given: A=1500 mm? AAL=3550…

Q: Sketch a flowchart showing the steps involved in the analysis of: Flexure in Doubly Symmetric Shapes…

A: We need to create a flowchart to explain how to build structural steel beams with doubly symmetric…

Q: A bar 500mm long and 200 mm in diameter is elongated by 1.2mm under axial pull of 105kn calculate…

A: Given :- Length of the bar (L) = 500 mm Diameter of the bar (D) = 200 mm Elongation due to pull =…

Q: A liquid with dynamic viscosity of 0,00275 kg/m.s and specific weight 9 KN/m' fills the space…

Q: A 100 m tape weighing 30 N is suspended between the two ends under a standard pull of 180 N. The…

Q: A compressive force P is applied to a 75mm by 100mm piece of wood. The wood grain makes a 20- degree…

A: To determine the largest axial load P that can be safely applied to the wooden column. Given,…

Q: A line was measured to be 625.35 m using a 50-m steel tape under a pull of 6 kg. The mean…

Q: Assuming F is 90lb, coefficient of static friction ps=0.2, and the coefficient of kinetic friction…

A: A weight is kept on inclined surface, kinematic , static friction coefficient, mass of body and…

Q: A steel tape weighing 0.75 kg has a cross-sectional area of 0.04 cm2. The tapemeasures exactly 30.00…

Q: A 5kg block is placed in a rough surface (u, = 0.30 and Hi = 0.25) inclined at a slope of 25 degrees…

Q: 0.20 cm 0.20 cm 3 cm 0.25 cm

Q: 20 kg B 4. The coefficients of friction are μ₁ = 0.40 and μ = 0.30 between all surfaces of contact.…

A: Determine the smallest force P required to start the 30-kg block moving.

Q: A 160-lb block rests on a horizontal surface, as shown. The coefficient of static friction is 0.4.…

A: Given weight of block =160lb coeff of friction =0.4 Maximum value of horizaontal force P?…

Q: A steel bar 106mm long and having a square cross section 20 mm (0.8 in.) on an edge is pulled in…

A: Calculate- elastic modulus of the steel Given- length = 106 mm -cross section= 20*20 mm² -load =…

Q: A 30 m tape weighs 12 g/m and has a cross sectional area of 0.020 cm?. It measures correctly when…

A: Given data: L=30 m W=12 g/m A=0.020 cm2 Standard pull=85 N Field pull=85 N Standard…

Q: A surveyor used a steel tape to lay-out two station exactly 1km apart. The standard length of a tape…

Q: Q2: . A crawler tractor, its weight is (29.75) tons, and its pulling force is (22700) kg. Find the…

A: Consider the given data Weigth of crawler tractor=29.75 tonspulling force=22700 kgRolling…

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied…

Q: A line was measured using a 30-m steel tape that is standardized at a temperature of 15°C and under…

A: solution Given the steel tape of length L =30mstandard temperature Tm=15°Cstandard pull Pm=8kgthe…

Q: Question 3 An 4.3 meter aluminum square wire is hanging vertically. A tensile load of 350 KN is…

A: As per bartleby policy i can do only one question at a time. Please upload again other questions.…

Q: A 10 kg block rest on an inclined plane making an angle of 30 degrees with the horizontal. a. find…

Q: A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown…

A: (a)Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type…

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

Q: A plate at 0.010 mm distant from a fixed plate, moves at 10 cm/s and requires a force of 1 N per…

A: given- speed du=10 cm/s=10×10-2 m/sdistance dy=0.010 mm=0.010×10-3 mshear stress τ=1 N/mm2=106 N/m2

Q: MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER From a 12.00 meter bridge span, a truck and trailer…

Q: A 30-meter steel tape is of standard length under a pull of 6 kilos and temperature of 20 degree…

Q: A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress…

A: Given data in question UDL Point load Span member length To find out Bending stress

Q: force developed between the crate and the surface. b. if the crate is originally at rest, determine…

Q: a

A: Given open cylindrical tank, with diameter d= 605 mm thickness t = 3.02 mm a= 40.10 MPa, b =…

Q: A Lecture hall in a Police Station has a concrete roof of 150 mm thick is subjected to the following…

Q: A steel rectangular block 1in wide, 1/2in deep and 4in long is subjected to an axial tensile load of…

A: b = 1in wide d = 1/2in deep L = 4in P = ∆L = 2.8×10-2in∆b = .21×10-2in

Q: a steel wire is 4m long and 2mm in diameter .how much is it elongated by 20kg body suspended on it ?…

A: Stress is defined as the ratio of the stress to the unit area applied. σ = PA =20×9.81π4×2×10-32…

Q: Describe the difference between Uniform wear and Uniform pressure.

A: Difference between Uniform wear and Uniform pressure:

Q: A 100 m tape is suspended between two ends under a pull of 165 N. The weight of the tape is 25 N.…

A: Given data : Applied pull (P)=165 N Weight of Tape (W)=25 N Length of tape supported between support…

Q: What is the average resistance required to stop a truck of mass 600 kg in a distance of 30 m, if…

A: Given data : Mass (m)=600 kgSpeed (U)=30 m/secDistance covered (S)=30 m

Q: 4) A plate is at a distance of 0.025 mm from a fixed plate and is moving at speed of 60 cm/s when a…

Q: A 185-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

Q: A simply supported beam carrying floor joist shown in Figure is made of rectangular wood having a…

Q: The crate has a weight of W = 350 lb, and the coefficients of static and kinetic friction are us 0.3…

Q: A 30 m steel tape exactly at a temperature of 20° C and pull of 10 kg were used in a practical class…

Q: Calculate its nominal moment strength (M.) of the section. 18 in. 24 in. 2 #8 Compressive strength…

A: Consider the following figure. First, find the position of the neutral axis that lies at a depth xu…

Q: A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is a=40° The…

Q: Water flows through a 600 mm diameter pipe with a velocity of 2.7 m/s. Bulk modulus of water is 2060…

Q: 1. A tape measure 1.25 cm wide x 0.40 mm thick having an elastic modulus E = 1.6 GPa is used to…

A: The dimension of the tape is 1.25 cm×0.40 mm. The elastic modulus is E=1.6 GPa. The actual length of…

Q: Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft^3 of the…

A: Given data : Increase in pressure (∆P)=150 psiInitial Volume( V)=10 ft3Decrease in Volume (dV)=0.02…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

A plate having size 12 by 15 meter is pulled with velocity
of .08 m/s over a fined plate at a distance of .3 mm with
the viscosity of .03N-sec/m2 . Find the Force.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A piece of steel wire 100 feet long, with a cross-sectional area of 0.004 aq. in., must be stretched with a pull of 16 pounds when in use . if the modulus of elacticity of steel is 30,000 psi: a) what is the total elognation in the entire length of the wire? b) what tensile stress is producted by the pull?
Calculate the shear modulus for a given cylindrical metal speciman and test results of T = 1500 N ⋅m, L = 20 cm, D= 5 cm, and ϕ = 0 02 rad . Can you tell what the material is?
A rectangular piece of wood, 50 mm x 100 mm in cross-section is used as acompression block as shown in the figure. Determine the maximum axial load P whichcan be safely applied to the block if the compressive stress in the wood is limited to 20MPa. (Ans. P = 100,000 N or P = 100 KN)
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 245.3 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: ___ MPa. Calculate your answer to one decimal place.
What is the bending moment from the controlling ASD load combination with dead load moment MD=5,000 lb-in and live load moment ML=10,000 lb-in? (units=lb-in) 15,000 10,000 5,000 22,000
A 10-lb force is pushing the 40-lb block as shown. The incline angle of the plane is α=40º . The coefficient of static friction between the block and the incline is μs = 0.75 and the coefficient of kinetic friction is μk = 0.65. Will the block slide on the plane? If it does, will it slide up or down the plane? What is the friction force between the block and the plane?
A 128.8 lb homogeneous plank is placed on two homogeneous, cylindrical rollers, each of weight 32.2 lb. The system is released from rest on a surface inclined 30-degrees to the horizontal (see figure below). Determine the initial acceleration assuming no slipping occurs. Does this initial acceleration change with time?
A 59 kN axial load is applied to a metal bar with a rectangular cross-section, 11 mm wide by 21 mm thick. While the load is applied, the bar elongates 2.5 mm. The modulus of elasticity and the Poisson's ratio are 100 GPa and 0.35, respectively. Assuming that the bar is still behaving elastically, how long is the original length of the bar in meters? Round your answer to 1 decimal place.
A 0.1m3 volume of water is observed to be 0.0982m3 after a pressure is applied. What is the applied pressure? Use bulk modulus of elasticity of water is 2110MPa.
Determine the total uniform distributed service load and total uniformly distributed ultimate load acting on the continuous beams of the second-floor plan of residential building shown in the figure. Draw the free body diagrams of the continuous beams using the ultimate load. 2ND FLOOR PLAN RC Column : 0.30m x 0.40m RC Beam : 0.30m x 0.50m RC Slab : 150mm thickness Floor Finish : Solid Flat tile on 25mm mortar base Ceiling : Suspended metal lath and gypsum plaster (placed below beam) Exterior wall : 100mm CHB (19.60 kN/cu.m mortar, full grout) plastered both sides.
Sketch a flowchart showing the steps involved in the analysis of: Flexure in Doubly Symmetric Shapes bent about the Major Axis
The figure shows the cross section of a circular steel tube that is filled with concrete and topped with a rigid cap. Calculate the stresses in the steel and in the concrete caused by the 200-kip axial load. Use Est = 29 x 106 psi and Eco = 3.5 x 106 psi.