A program will be written in C language for a microwave oven. The desired features of the microwave oven areas follows: 2 buttons will be used to adjust how many seconds the microwave oven will work. One button is forincreasing and the other for decreasing. Each time the button is pressed, the working time will be determinedin 5 second intervals. 1 button will be used to determine the operating power (watts) of the microwave oven. The power ratingsare: 200, 300, 450, 600, 750, 800.(You can think of them as operating modes, not numerical values. Such as mod1=200, mod2=300 etc.According to the selected mode number, the leds arranged side by side will be turned on. For example; Ifmod3 is selected, 3 leds will be on, if mod4 is selected, the 4th led will also be on.) After the operating time and operating mode are set, the start button will be pressed and the microwave ovenwill be started. When the oven starts to work, the timer will count down and the motor that rotates the tableinside will rotate at a constant speed. When the operation of the microwave oven is completed, a message should be sent from the serial port as"operation complete" and the buzzer connected to P1.0 should operate at 1 second intervals for 20 seconds.Write the required C code by adding your comments to the important places and test the code you wrote in proteus A program will be written in C language for a microwave oven. The desired features of the microwave oven areas follows:• 2 buttons will be used to adjust how many seconds the microwave oven will work. One button is forincreasing and the other for decreasing. Each time the button is pressed, the working time will be determinedin 5 second intervals.• 1 button will be used to determine the operating power (watts) of the microwave oven. The power ratingsare: 200, 300, 450, 600, 750, 800.(You can think of them as operating modes, not numerical values. Such as modl=200, mod2=300 etc.According to the selected mode number, the leds arranged side by side will be turned on. For example; Ifmod3 is selected, 3 leds will be on, if mod4 is selected, the 4th led will also be on.)After the operating time and operating mode are set, the start button will be pressed and the microwave ovenwill be started. When the oven starts to work, the timer will count down and the motor that rotates the tableinside will rotate at a constant speed.When the operation of the microwave oven is completed, a message should be sent from the serial port as"operation complete" and the buzzer connected to P1.0 should operate at 1 second intervals for 20 seconds.Write the required C code by adding your comments to the important places and test the code you wrote in proteus

C program use to answer the question

A program will be written in C language for a microwave oven. The desired features of the microwave oven are as follows: • 2 buttons will be used to adjust how many seconds the microwave oven will work. One button is for increasing and the other for decreasing. Each time the button is pressed, the working time will be determined in 5 second intervals. • 1 button will be used to determine the operating power (watts) of the microwave oven. The power ratings are: 200, 300, 450, 600, 750, 800. (You can think of them as operating modes, not numerical values. Such as modl=200, mod2=300 etc. According to the selected mode number, the leds arranged side by side will be turned on. For example; If mod3 is selected, 3 leds will be on, if mod4 is selected, the 4th led will also be on.) After the operating time and operating mode are set, the start button will be pressed and the microwave oven will be started. When the oven starts to work, the timer will count down and the motor that rotates the table inside will rotate at a constant speed. When the operation of the microwave oven is completed, a message should be sent from the serial port as "operation complete" and the buzzer connected to P1.0 should operate at 1 second intervals for 20 seconds.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Question

A program will be written in C language for a microwave oven. The desired features of the microwave oven are
as follows:
 2 buttons will be used to adjust how many seconds the microwave oven will work. One button is for
increasing and the other for decreasing. Each time the button is pressed, the working time will be determined
in 5 second intervals.
 1 button will be used to determine the operating power (watts) of the microwave oven. The power ratings
are: 200, 300, 450, 600, 750, 800.
(You can think of them as operating modes, not numerical values. Such as mod1=200, mod2=300 etc.
According to the selected mode number, the leds arranged side by side will be turned on. For example; If
mod3 is selected, 3 leds will be on, if mod4 is selected, the 4th led will also be on.)
 After the operating time and operating mode are set, the start button will be pressed and the microwave oven
will be started. When the oven starts to work, the timer will count down and the motor that rotates the table
inside will rotate at a constant speed.
 When the operation of the microwave oven is completed, a message should be sent from the serial port as
"operation complete" and the buzzer connected to P1.0 should operate at 1 second intervals for 20 seconds.

Write the required C code by adding your comments to the important places and test the code you wrote in proteus

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.