A pump forces 1.2 m^3/min of water horizontally from an open well to a closed tank where the pressure is 0.9 MPa. Compute the work the pump must do upon the water in an hour just to force the water into the tank against the pressure * 1080 kJ/min 1000 kJ/min 66420 kJ 6080 kJ 1080 kJ 9464 kJ

A pump forces 1.2 m^3/min of water horizontally from an open well to a closed tank where the pressure is 0.9 MPa. Compute the work the pump must do upon the water in an hour just to force the water into the tank against the pressure * 1080 kJ/min 1000 kJ/min 66420 kJ 6080 kJ 1080 kJ 9464 kJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: In the fluidized bed as the velocity increases above the minimum fluidization velocity the bed heigh...

A: Given :- In the fluidized bed as the velocity increases above the minimum fluidization velocity the ...

Q: An adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrig...

A: For R134 table the value is chosen at 20 and 50 degree hliq,50=hliq,20+xhevap,20123.515=25.47+x(212....

Q: Which one of the following is correct for horizontal deflection of the electron beam in a CRO? ...

A: Which one of the following is correct for horizontal deflection of the electron beam in a CRO? I...

Q: Why hardness test needs to perform in engineering practice?

A: The hardness test is performed in engineering practice to determine the properties of the materials ...

Q: Pr1. A ladder consists of two legs of mass m attached together by a frictionless joint. The ladder i...

A: The free body diagram of the ladder is given below,

Q: 2850 kg/day = O a. 11.3 kg/s O b. 14.8 kg/s O c. 3.2 kg/s O d. 0.33 kg/s

Q: Q1: A spherical container of inner radius ri=40 cm, outer radius r2-41 cm (k=1.2 W/m°C) is used to s...

A: Assumption:- 1) Heat Transfer takes place in One dimension 2) Material is isotropic

Q: Answer 6-4, Convert english to metric units and draw FBD. Write your step by step solutions.

A: Consider the influence line diagram shown below for the left support as shown below.

Q: Q 4. Determine longitudinal stress in the cylinder if it has wall thickness of 7 mm and subjected to...

A: Given data: The thickness of the cylinder is t = 7 mm. The internal pressure is P = 100 MPa.

Q: Six nails are used to hold the hanger at A against the column. Determine the minimum required diamet...

A: given Six nails are used to hold the hanger at A against the column.diameter of each nail to the nea...

Q: The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter...

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and s...

Q: An aerospace engineer is designing a hover board for a project demonstration. He/She plans to use a ...

A: Write the given values along with suitable variables. D = 3 ft = 0.9144 m Area = A = π r2 = (22/7) (...

Q: P7-8. A loading causes the member to deform into the dashed shape. Explain how to determine the norm...

A: Given: To determine normal strains of AB and CD

Q: In a centrifugal pump, the liquid enters the pump _________ a.At the centre b.At the top c.From sid...

Q: A 5-kg collar A is at rest on top of, but not attached to, a spring with stiffness k1 = 400 N/m when...

A: Use the method of work and energy applied to the collar A. Now as the collar is initially at rest s...

Q: (i) Discuss about Surface tension with the help of a diagram. (ii) Discuss about the different patte...

A: Surface tension:-

Q: Which of the following is true O a. Piezometer can be applicable for high pressure measurements O b....

A: Piezometer is a device used to measure the pressure of a liquid. A tube is attached to the liquid f...

Q: To cool hot oil, an engineer has suggested that the oil be pumped through a pipe submerged in a near...

Q: Determine the y coordinate of the centroid of the shaded area in terms of r1, r2, and a.

A: y2¯=23r2sin(π2-α)(π2-α) A2=(π2-α)r22y2¯=23r2cosα(π2-α)y1¯=23r1cosα(π2-α) A1=(π2-α)r12

Q: Practice Problem 3.4.7: The resultant of the three forces is the force R =-170j kN acting through po...

Q: 17. The pressure head in a gas tank is 2.75 atmosphere. Compute the pressure head in meters of water...

Q: 3. Write any 2 advantages of fossil Energy A) B) 4. Write any 2 advantages of Alternate Energy A)

A: given: write two advantage of fossil and alternate energy.

Q: A car and truck are both traveling with a constant speed of 20m/s. The car is 10m behind the truck. ...

A: Given Data Velocity of car and truck is: V=20 m/s Deceleration of the truck is: a=-2 m/s2 The time...

Q: The cooling rate (in °C/s) at the center of a shaft with diameter d (in mm) is given by the followin...

A: Data given - For alloy A C = 0.3 , Mn = 0.8 , Cr = 0.50. , Mo = 0.2, Ni = 0.55

Q: In a gas turbine plant __________________ is used to increase the turbine output a.heat exchanger b....

A: Given data In a gas turbine plant __________________ is used to increase the turbine output

Q: The following is (are) the limitation(s) of gas turbines. a.Low efficiencies at part loads b.All ...

A: The limitations of gas turbines are: a) Low efficiencies at part loads d) They are not self starting...

Q: Mr. Mohammed is working in CNC machine of a shaft manufacturing company. This machine ram is moved i...

A: Accumulators: The hydraulic accumulators are used to store the energy just like batteries. They used...

Q: A car and truck are both traveling with a constant speed of 20m/s. The car is 10m behind the truck. ...

A: Given data: Speed of car and truck = 20 m/s Distance between car and truck = 10 ...

Q: Junk mill uses which action during fishing operation? a. Falling b. Tearing c. Grinding d. Crus...

A: A junk mill and a boot basket are used to pick up fish from the well. In this situation, the junk mi...

Q: For each of the plates and loadings shown, determine the reactions at A and B.

A: Ans(a) ∑MA=0B(20)-50(4)-40(10)=0B=30lb∑Fx=0Ax+40=0Ax=-40lb∑Fy=0Ay+B-50=0Ay+30-50=0Ay=20lbA=Ax+Ay=402...

Q: Water at 15°C flows at a depth of 0.25 m with an average velocity of 7 m/s in a rectangular channel....

A: Given Data⇒depth =0.25 mvavg=7msrectangular channel

Q: The relation between pressure and flow rate for centrifugal pump is:

A: A centrifugal pump is a mechanical device which is used to move a fluid by means of the transfer of ...

Q: Situation 2: Water flows at a rate of 0.8 cumecs in a 900 m-long pipe with a total head loss of 4m. ...

A: As per the Bartleby guidelines, only one question can be answered at a time. Therefore, please resub...

Q: A 3.7kg body is suspended from a spring of constant k = 6.1kN/m. At time t = 0, it has a downward ve...

A: Given Mass, m = 3.7 kg Spring constant, k = 6.1 kN/m Find System period, ...

Q: A rigid tank is divided into two equal parts by a partition. One part of the tank contains 4 kg of c...

A: According to the second law of thermodynamics, A new property of a system can be introduced i.e, Exe...

Q: Heavy lifting work is often accomplished by shifting fluids in big machines. The power system of suc...

Q: Normally when the creep is considered in materials?

A: given: Normally when the creep is considered in materials?

Q: An airplane engine intakes air. adds fuel to burn the air and exhausts the burnt gases to generate t...

Concept explainers

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.

Question

Please check the attached file

A pump forces 1.2 m^3/min of
water horizontally from an open
well to a closed tank where the
pressure is 0.9 MPa. Compute
the work the pump must do
upon the water in an hour just
to force the water into the tank
against the pressure *
1080 kJ/min
1000 kJ/min
66420 kJ
6080 kJ
1080 kJ
9464 kJ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Seven hundred gallons per minute of water are being discharged by a centrifugal pump 5 ft above the pump inlet. The inlet pressure is 4-in Hg above the atmospheric and the discharge pressure is 29 psia. If the pump has an 8-in diameter inlet and a 4-in diameter discharge, find the pump efficiency. Assume the pump input is 8Hp.A. 55%B. 64%C. 73%D. 84%
A pump sends a substance (sg=1.9) from a tank to a tank placed at a higher level, where the velocity is 1 m/s. Considering that the friction losses in the system are 5.8 m and the efficiency of the pump is 68%, find the nominal power of the pump and the pressure developed by it. D4= 6cm D5= 8cm H3= 12m
A pump forces 1 m3/min of water horizontally from an open well to a closed tank where the pressure is 0.9 MPa. If the work done upon the water had been used solely to raise the same amount of water vertically against gravity without change of pressure, how many meters would the water have been elevated? What velocity would the water have reached in m/s? If the work had been used to accelerate the water from anitial velocity of 10 m/s, what would the final velocity have been in m/s? Ans. (91.74 m ; 42.4 m/s; 43.6 m/s)
A small centrifugal pump, when tested at N = 2875rpm with water, delivered Q = 252 gpm and H = 42 meters at its best efficiency point of 76%. Determine the specific speed of the pump and the required power input to the pump.
A centrifugal fan supplies 4.7m3/s of air at a total static pressure of 325Pa. If the fan efficiency is %06 and rotates at a speed of 950rpm and supplies air with a velocity of 12m/s, determine the fan total pressure, air power, and fan power?
Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations (1)Q=10.75m3/s (2)P=204kw/273hp
A turbine is discharging 10m3/s under a head of 22 m at 200 rpm. The efficiency is 90%. Determine the performance of turbine under a head of 44 m.
PAY ATTENTION TO THE QUESTION : What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answer
A pump is used to increase the pressure of water from 100 kPa to 900 kPa at a rate of 160 L/min. If the shaft power input to the pump is 3 kW, the efficiency of the pump is (a) 0.532 (b) 0.660 (c) 0.711 (d ) 0.747 (e) 0.855
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above
A mini hydro power station takes in 3 cubic meters per second of water from a wide open reservoir through its turbine from an elevation of 15 meters and discharges to its surroundings at 0.50 m/s. During data gathering, the rotational force of the turbine shaft is measured 250 N for a distance of 2 m from its center axis at 2,850 rpm. If the electrical generator is 88% efficient, determine the turbine efficiency and the electrieity output of this station. Show the energy or schematie diagram and label it accordingly.