A reducing elbow is used to deflect waterflow at a rate of 14 kg/s in a horizontal pipeupward 30°. The elbow discharges waterinto theatmosphere. Thedifference between the centers of theoutlet and the inlet is 30 cm. The weight ofelevationthe elbow and the water in it is consideredto be negligible. Determine the anchoringforce (F) needed to hold the elbow inRxplace. Given that other force F acts on theelbow which is equal 500 NA=7 cm2.A-113 cm30 cm Select one:a.-2059.44 Nb.-4059.44 NC. -3059.44 Nd. -2559.44 Ne. -3559.44 N

Answered: A reducing elbow is used to deflect…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Flood in irrigation areasto block and return the water to the river or wateras below to guide your bedThe flat cover system provided is preferred. Of coverits weight is 871 kg. Square section cover, coverhinged 1 m above center (a = 0.25 m)and b = 150 cm. Cover vertically 4 °has angle. According to the givenWhat is the maximum water head (h) for not openingshould be up. (ρ water = 1000 kg / m3)
A 7-cm diameter vertical water jet is injected upwards by a nozzle at a speed of 15 m/s. Determine the maximum weight of a flat plate that can be supported by this water jet at a height of 8m from the nozzle.
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
An 8-cm-diameter horizontal water jet having a velocity of 35 m/s strikes a vertical stationary flat plate. The water splatters in all directions in the plane of the plate. How much force is required to hold the plate against the water stream?
Water enters vertically and steadily at a rate of 10 L/s into the sprinkler shown. Both water jets have a diameter of 1.2 cm. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating
A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
What do you notice about the total momentum before and the total momentum after? Which principle are you demonstrating here? State it. Discuss what is meant by an isolated system and how it is related to the law of conservation of momentum.
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
A 90° elbow is directs water upwards into the atmosphere from a horizontal pipe with a diameter of 12 cm that is flowing at 20 L/s. The elevation difference between the centers of the exit and the inlet of the elbow is 35 cm. If the weight of the elbow and the water in it are negligible, and assuming a momentum-flux correction factor of 1.03, determine the anchoring force needed to hold the elbow in place.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS