A refrigerator operating on the Carnot cycle is used to make ice. Water freezing at 32oF is the cold reservoir. Heat is rejected to a river at 72oF. Determine the work required to freeze 2000 lbm of ice if the energy required to freeze ice is 144 Btu/lbm. What is the power input required in kW and hp is this operation is carried out in 1 hour?

Question

A refrigerator operating on the Carnot cycle is used to make ice. Water freezing at 32oF is the cold reservoir. Heat is rejected to a river at 72oF. Determine the work required to freeze 2000 lbm of ice if the energy required to freeze ice is 144 Btu/lbm. What is the power input required in kW and hp is this operation is carried out in 1 hour?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

IC Engines

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: BOILER |Pump Exit T, = 40°C P1 = 15.0 MPa Boiler Exit T2 = 550°C P2 = 15.0 MPa The pump shown in the...

A: Given data as per question Mass flow rate = 36000 kg/hr = 36000/3600 = 10 kg/s Exit temperature = 40...

Q: Marked out of 1.00 Flag question A fluid jet (S=1.4) of velocity V, =20 m/st %3D20m/s impinges norma...

A: Given data,  

Q: 19-58. The pendulum consists of a 10-lb solid ball and 4-lb rod. If it is released from rest when 60...

A: Given data:

Q: Exercise 2: Determine the unextended length (l_0) of spring AC, if a force    P = 80 lb generates th...

A: Given data as per question  force    P = 80 lb  spring deformation constant as k = 50 lb / ft.  θ = ...

Q: A force of P = 500 N is applied to the 80-kg cart. Determine the reactions at both the wheels at A a...

A: Given data as per question force of P = 500 N MASS = 80 kg

Q: Identify the zero-force members in each truss

A: There are two rule to identify zero force in the truss members:- (a) Let's consider a joint which is...

Q: I downloaded this question multiple times but I had no answer. I need 6  I have to get answer for it

A: The properties required for mechanical design are: Strength- The strength is measured by the maximu...

Q: What is spin in gyroscopic motion?

A: Consider a disc rotating with angular velocity ωs as shown in the figure below,

Q: One of the following is a surface force Select one: a. pressure b. electrostatic magnetic C. d. grav...

A: Pressure –it is defined as the ratio of the force and the area. Which means its values can be depend...

Q: A structure ABCD is supported by a slider bearing at A, the cable BE and a thrust bearing at D. If t...

A: Draw the free-body diagram of the system.

Q: The strength per meter of the longitudinal joint in the figure is 480 kN, whereas or the girth joint...

A: Given data:

Q: F3-33. Replace the loading by an equivalent resultant force and specify where the resultant's line o...

A: Let the line of action of equivalent resultant force be at x from A as shown below – The equivalent...

Q: At the beginning of a trip you are traveling due north at 120 km/hour. At the end, you are traveling...

A: Consider v1 as the initial velocity and v2 as the final velocity. Draw the vector diagram of the ini...

Q: 20-23. The differential of an automobile allows the two rear wheels to rotate at different speeds wh...

A: Write the expression velocity of the horizontal gear. Understand the velocity of gear H and gear G....

Q: A 1750 rpm centrifugal pump equipped with an 11-in.-diameter impeller requires 14.3 bhp when deliver...

A: Given :  

Q: a: The magnitude of the shear stress at r=3in (outer fiber of shaft) is? b: The magnitude of the max...

A: The expression of the applied torque is written as The expression of the polar moment of inertia of...

Q: The monthly usage for a component supplied to an assembly plant is 3,400 parts.  There are 21 workin...

A: Given : Number of parts = 3400 Number of working days = 21 The effective operating time (EOT) of the...

Q: 6. Answer the following questions regarding the Lever Rule. [ a. Describe the purpose of the Lever R...

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,...

Q: The textbook answer is provided. Please do a detailed solution.

A: Consider the beam to be of a uniform cross-section, the material used is isotropic and homogenous an...

Q: The pumping power of the human heart is approximately 2W (assuming a normal cardiac output of 5 lite...

A: Given data: (a)

Q: A house has two rooms. One is much larger than the other such that the wall area is twice the size o...

A: Rate of heat transfer is inversely proportional to the thickness of the wall. Thicker the insulation...

Q: The pendulum consists of a 4-kg circular plate and a 2-kg slender rod. Determine the radius of gyrat...

A: Since the pendulum is hinged about point O. Then this pendulum will rotate about O. Calculate the ma...

Q: A rod AB is supported at A by a ball and socket joint and two caples of BC and BD. If the weight (W)...

A: Consider the diagram shown below for the given system. In the above diagram, the angles are with th...

Q: 3-43. If F = 450 N, determine the magnitude of the moment produced by this force about the x axis. 1...

A: The Cartesian force vector can be calculated as

Q: For the Howe bridge truss shown, d=11 ft ,F1=3250 lb, F2=2150 lb, F3=2450 lb, and F4=3950 lb. Determ...

A: The free-body diagram of the truss is given as, Now, apply the force equilibrium in the horizontal ...

Q: Discuss the difference in potential energy between weight and spring. plzzzz!!!!

A: Potential energy exists by the virtue of the relative position of the body, stresses inside the body...

Q: below. Its dimensions are 1 m x 1 m. What moment is needed to start the trap door lifting? Assume th...

A: Consider W as the weight of the door and Rx and Ry as the reaction at the hinge in the x and y-direc...

Q: 19–38. The plank has a weight of 30 lb, center of gravity at G, and it rests on the two sawhorses at...

A: Write the expression of mass moment of inertia at point G. Write the expression of the mass moment ...

Q: A 200-kg cylinder is hung by means of two cables AB and AC that are attached to the top of a vertica...

A: Consider the diagram shown below for the given system. Here, TAB and TAC are the tension in the str...

Q: Specifically a dynamics problem. Question in pic below. Answer: omega = sqrt[(omega0)2 + (g/r2)s sin...

A: Write the expression of the mass moment of inertia of the ring. Consider h as the horizontal distan...

Q: Below is a continuous cooling transformation curve for steel (upper) and for a silicate melt (lower)...

A: (a) Critical cooling rates: For steel: critical cooling rate for the steel is the minimum cool rate...

Q: The simple pendulum (figure shown in Question 2) consists of a light but rigid bar of length L=0.3 m...

A: Given data as per question  L=0.3 m mass M = 9.1 kg.  angular velocity  = 5 rad/s,  mass m = 1.6 kg,...

Q: Answer as soon as possible

A: Given data as per the question Uniform distributed load value = 2.5 k/ft data is taken as from the ...

Q: Identify the zero force members in the truss

A: There are two rule to identify zero force in the truss members:- (1) Let's consider a joint which is...

Q: The product stream flow rate is 380 kmol/h

A: Write the expression of the volumetric flow rate.

Q: The collar of mass m is released from rest while in position A and subsequently travels with neg- li...

A: (a) Draw the free-body diagram of the collar just before the collar passes point B, Here, N is the ...

Q: A bar with a length of 7 inches is stretched to 7.1 inches. What is the strain in the bar?

A: The length of the bar Lo = 7 inches The stretched length of the bar Lf = 7.1 inches

Q: Mechanical Engineering Question

A: The diagram of the pipe is given as, The diameters in section 1 and section 2 are the same. The vel...

Q: a: What is the magnitude of torque applied to the shaft? b: The magnitude of the Polar Moment of Ine...

A: The expression of the applied torque is written as

Q: otal head pressure 1 m2 and m2. n.

A: Write the expression of the head of the water flow from the nozzle.

Q: The two steel shafts in Fig. have the same diameter and weigh 100 lb each. Neglecting friction at co...

A: Consider the diagram shown below for the given system,

Q: Water enters a centrifugal pump axially at atmospheric pressure at a rate of 0.10 m3/s and at a velo...

A: Given data as per question Rate of water entering = 0.10 m3/s Velocity = 6 m/s Density of water = 10...

Q: Apply the necessary symbology to establish the required tolerance and datum feature(s) to control th...

A: The datum for the given part can be assumed as shown below,

Q: Figure below shows an aircraft fighter. The wing of the aircraft may be modelled as a clamped wing w...

A: Write the equation of motion of mass m1. Write the equation of motion of mass m2. Consider the fol...

Q: Please I want answer for this question - 5 . Many Thanks

A:   Given data as per the question Radius of quadrant = 275 cm = 2.75 m Width of the gate = 750 mm =0....

Q: 15-2. A 20-lb block slides down a 30° inclined plane with an initial velocity of 2 ft/s. Determine t...

A: Given data: Mass of block, m = 20 lb Initial velocity, v1 = 2 ft/s Time, t = 3s Coefficient of kinet...

Q: A force F has the components Fx= 20 lb, Fy =−30 lb, and Fz =60 lb. Determine its magnitude F and the...

A: Given data: Fx = 20 lb Fy = -30 lb Fz = 60 lb The magnitude of force is calculated by using the form...

Q: Determine the moment M of section ABC of the beam shown below as a function of position x (from A to...

A: Given : T=W=10 kN MB = Tsinθ(BD)  

Q: The shown spool has a mass of 100 kg and radius of gyration of 0.3 m. For P = 70 N and µ, = Hk = 0.2...

A: Given data: Consider the free body diagram of the spool as shown below, Here, Fr is the friction f...

Q: The structure of a football goal is shown in the figure below. The bending motion of the structure c...

A: When the soccer ball hits the crossbar then apply the conservation of linear momentum, Here, vo is ...