A reinforced concrete pier is used to support the stringers for a bridge deck. Draw the shear and moment diagrams for the pier when it is subjected to the stringer loads shown. Assume the columns at A and B exert only vertical reactions on the pier. 60 kN 60 kN 35 kN. 35 kN 35 kN 1.5m 1.5m 2.0 m | 2.0 m ]1.5m 1.5 m

A reinforced concrete pier is used to support the stringers for a bridge deck. Draw the shear and moment diagrams for the pier when it is subjected to the stringer loads shown. Assume the columns at A and B exert only vertical reactions on the pier. 60 kN 60 kN 35 kN. 35 kN 35 kN 1.5m 1.5m 2.0 m | 2.0 m ]1.5m 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
Material A (shown below) is experiencing forces shown below at different points along its body. If the area of its cross section is equal to 0.35 in^2, determine the total new length of the material if modulus of elasticity is equal to 5x10^6 psi. AB =4 ft BC =4.5 ft, CD = 3.5 ft. Note: Final Answer in 4 decimal places.
A rectangular concrete slab, 3 m x 4.5 m, rests on the surface of a soil mass. The load on the slab is 2025 kN. Determine the vertical stress increase in kPa at a depth of 3 m under the midpoint of the 4.5 m right edge. a.13.5 b.47.4 c.63 d.102.4
A flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates is shown in the figure. The plates are 160mm long and 80mm wide. (a) Determine the force that can be applied to the arrangement, if it is not to exceed a shear stress of 350kPa
The hub of a flange coupling has a diameter of 135 mm. The flange has a thickness of 20 mm. Determine the force that can shear the hub from the flange coupling if the shear stress of the flange is 200 MPa. A. 1 984.2 kN B. 1 343.4 kN C. 1 152.3 kN D. 1 696.5 kN
A straight girder of uniform section and length L rests on supports at the ends, and is propped up by a third support in the middle. The weight of the girder and its load is w per unit length. If the central support does not yield, prove that it takes a load equal to (5/8)wL. ANSWER: 1.80cm and 2.48cm Please show solution to the answer.
a) 1. The support reaction forces at the A and C, in terms of P,be careful of the sign. 2. Give the expressions of the shear and moment at an arbitrary poistion x of AB segment, in terms of P and x, be careful of the sign. 3. Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, in terms of P and x, be careful of the sign. b)Given l= 1000 mm, P= 4000 N and l1/l=0.66, calculate the internal shear force and draw the moment diagram
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
A prestressed hollow box cross section is shown in the figure. The area of prestressed reinforcement in the tension zone is 1148 mm2. Use grade 270 for seven wire-strand tendons. fpy = specified yield strength of tendons fpu = specified tensile strength o pre stressing tendons fse = effective prestress after losses fse = 1022 MPa Aps = 1148 mm2 fpy = 0.95fpu fc’ = 34.5 MPa fpu = 1860 MPa a. Compute the Yp factor. b. Compute the stress in prestressed reinforcement at nominal strength. c. Compute for the design moment capacity. d. Compute the effective pre stressing force after losses of stress e. Compute the depth of the compression block. f. Compute the pre stressing steel ratio.
A T- section is the cross section of a loaded beam as shown.Given: U1= 20 kN/m; M1 = 100 kN-m; P1 = 120 kN a.) Draw the shear diagram using graphical solutionb.) Determine maximum shearing stress.b.) Determine the shearing stress at the junction of the T-section.
To analyze a beam subjected to a vertical force and a triangular distributed load, determine the reaction forces acting on each of the supports, determine the minimum pin diameter for one support subjected to single shear, and determine the average shear stress in a pin support subjected to double shear. As shown, beam BC is subjected to a load of magnitude P = 780.0 kN and a triangular distributed load of w = 510.0 kN/m. The support rod AB is oriented at an angle of θ = 150.0 ∘ from the beam. Let a = 4.000 m and b = 13.00 m . Cross-sectional views are shown for B and C. Determine the reaction force at B. Determine the reaction force at C. If the average shear stress in the material is not to exceed τavg = 150.0 MPa , determine the minimum required diameter for the pin at B. If the diameter of the pin is d = 125.0 mm, what is the average shear stress in the pin at C.
To analyze a beam subjected to a vertical force and a triangular distributed load, determine the reaction forces acting on each of the supports, determine the minimum pin diameter for one support subjected to single shear, and determine the average shear stress in a pin support subjected to double shear. As shown, beam BC is subjected to a load of magnitude P= 780.0 kN and a triangular distributed load of w = 510.0 kN/m. The support rod AB is oriented at an angle of θ = 150.0 ∘ from the beam. Let a = 4.000 m and b = 13.00 m . Cross-sectional views are shown for B and C. 1) Part A: Determine the reaction force at B. 2) Part B: Determine the reaction force at C. 3) Part C: If the average shear stress in the material is not to exceed τavg = 150.0 MPa, determine the minimum required diameter for the pin at B. 4) Part D: If the diameter of the pin is d = 125.0 mm, what is the average shear stress in the pin at C.