A sand casting mold is shown. All bottom and side plates have a uniform thickness of 1". The bottom plate is 10" by 5". The side plates have a width of 5" and height of 4". The outside diameter of the tube is 3" and inside diameter is 2 ". The tube height is 4". The inside hole of the tube extends to the end of the bottom plate. Ignore the plate that is connected to the side of the tube. Ignore all the curved corners. min Design a cylindrical riser with the height of 4" for this mold. The mold constant is 25 in2

A sand casting mold is shown. All bottom and side plates have a uniform thickness of 1". The bottom plate is 10" by 5". The side plates have a width of 5" and height of 4". The outside diameter of the tube is 3" and inside diameter is 2 ". The tube height is 4". The inside hole of the tube extends to the end of the bottom plate. Ignore the plate that is connected to the side of the tube. Ignore all the curved corners. min Design a cylindrical riser with the height of 4" for this mold. The mold constant is 25 in2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the casting of the part, whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and finally the mold in the most suitable form for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.)
Determine the time required to fill the mold cavity along with the riser as shown in the following figure.
A vertical centrifugal casting process is used to produce bushings that are 0.2 m outside diameter and 0.2 m in long. If the rotational speed during solidification is 500 rpm, determine the inside diameter at the bottom of the bushing if the diameter at the top is 0.084 m. * Add file
compute the diameter of the sphere (mm) that will freeze in the same time in same casting process with a 62.5mm x 150mm x 225mm plate. Assume that constant mold for this casting is 55 mm^2/s
A grey cast iron block of dimension 200 mm × 100 mm × 10 mm is produced by sand casting . Pattern making allowance is 10 %. What is the ratio of volume of the parttern to volume of the casting.
A cubical casting of 100 mm side is to be made from steel using an Al pattern (master pattern). For preparing the master pattern, a wooden pattern is used. Determine the dimensions of master pattern and wooden pattern. Use shrinkage allowance (mm/mm) for steel and Al as 0.021 and 0.013 respectively
The height of the down sprue is 175 mm and its CS are at the base is 200 mm² The CS area of the horizontal runner is also 200 mm² Assuming no losses, indicate the correct choice for the time (second) required to fill a mould cavity of volume 106 mm³ (Use g=10 m/s^ 2 )
For the sand casting of the part whose perspective pictures are given below, take into account the surface of the section, the model design, if necessary, the core design, all the molding stages and and finally draw the most suitable form mold for casting, and name all the mold elements by showing them on the figure (Note: The hole shown in the figure, full hole.) please draw the shapes more clearly and remember to draw each step.Thank you in advance
Show me a complete solution.
A aluminium alloy casting has a cylindrical geometry with 100mm in diameter and weighs 3200 gram. This casting takes 7.5 min to completely solidify. Another smaller and lighter cylindrical-shaped casting with the same diameterto-length ratio weighs 1800 gram. This casting is made of the same aluminium alloy and the same conditions of mold and pouring were used. Determinea) The mold constant in Chvorinov’s Rule,b) The dimensions of the lighter castingc) The total soldification time of the lighter casting. The density of aluminium alloy= 2.7 gram/cm3and n=2
Determine angle of repose for the given powder sample having the height of the powder pile=5inches and diameter of the powder pile=26 inches and mention the flow property.
5 The line separating the two parts of mold (cope and drag) is called___. a. Riser b. Parting line c. Gate d. Runners