A series RL circuit is shown below. Which of the suggested changes in the circuit would result in the final voltage across the resistor (a long time after the switch is closed) to be double what it is for the original circuit? 1. Reduce the resistance in the circuit to R/2 II. Double the inductance in the circuit to 2L III. Increase the voltage source to 21. O only change III None of the changes achieves the desired result O only change I O only change I O Changes I and II must be done together,

A series RL circuit is shown below. Which of the suggested changes in the circuit would result in the final voltage across the resistor (a long time after the switch is closed) to be double what it is for the original circuit? 1. Reduce the resistance in the circuit to R/2 II. Double the inductance in the circuit to 2L III. Increase the voltage source to 21. O only change III None of the changes achieves the desired result O only change I O only change I O Changes I and II must be done together,

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter23: Electromagnetic Induction, Ac Circuits, And Electrical Technologies

Section: Chapter Questions

Problem 102PE: An RLC series circuit hag a 1.00 k(register, a 150 (H inductor, and a 25.0 nF capacitor. (a) Find...

See similar textbooks

Similar questions

The capacitor in Figure 23.55(a) is designed to filter low—frequency signals, impeding their transmission between circuits. (a) What capacitance is needed to produce a 100 k reactance at a frequency of 120 Hz? (b) What would its reactance be at 1.00 MHz? (c) Discuss the implications of your answers to (a) and (b).
An RLC circuit consists of a 150- resistor, a 21.0-F capacitor, and a 466-mH inductor connected in series with a 120-V, 60.0-Hz power supply. (a) What is the phase angle between the current and the applied voltage? (b) Which reaches its maximum earlier, the current or the voltage?
A step-up transformer is designed so that the output of its secondary winding is 2000 V(rms) when the primary winding is connected to a 110-V (rms) line voltage, (a) If there are 100 turns in the primary winding, how many turns are there in the secondary winding? (b) If a resistor connected across the secondary winding draws an rms current of 0.75 A. what is the current in die primary winding?
When a wire is connected between the two ends of a solenoid, the resulting circuit can oscillate like an RLC circuit. Describe what causes the capacitance in this circuit.
Neon signs require 12-kV for their operation. A transformer is to be used to change the voltage from 220-V (rms) ac to 12-kV (rms) ac. What must the ratio be of turns in the secondary winding to the turns in the primary winding? (b) What is the maximum rms current the neon lamps can draw if the fuse in the primary winding goes off at 0.5 A? (C) How much power is used by the neon sign when it is drawing the maximum current allowed by the fuse in the primary winding?
An RLC series circuit has a 2.50 (resistor, a 100 (H inductor, and an 80.0 (F capacitor. (a) Find the circuit's impedance at 120 Hz. (b) Find the circuit’s impedance at 5.00 kHz. (c) If the voltage source has Vrms = 5.60 V, what is Irms at each frequency? (d) What is the resonant frequency of the circuit? (e) What is Irms at resonance?
Your RL circuit has a characteristic time constant of 20.0 ns, and a resistance of 5.00 M (a) What is the inductance of the circuit? (b) What resistance would give you a 1.00 ns time constant, perhaps needed for quick response in an oscilloscope?
Check Your Understanding A transformer steps the line voltage down from 110 to 9.0 V so that a current of 0.50 A can be delivered to a doorbell (a) What is the ratio of the number of turns in the primary and secondary windings? (b) What is the current in the primary winding? (c) What is the resistance seen by the 110-V source?
Presbycusis is a hearing loss due to age that progressively affects higher frequencies. A hearing aid amplifier is designed to amplify all frequencies equally. To adjust its output for presbycusis, would you put a capacitor in series or parallel with the hearing aid's speaker? Explain.
An AC generator with an output rms voltage of 36.0 V at a frequency of 60.0 Hz is connected across a 12.0-F capacitor. Find the (a) capacitive reactance, (b) rms current, and (c) maximum current in the circuit. (d) Does the capacitor have its maximum charge when the current takes its maximum value? Explain.
The current in the RL circuit shown here increases to 40% of its steady-state value in 2.0 s. What is the time constant of the circuit?
An RLC series circuit hag a 1.00 k(register, a 150 (H inductor, and a 25.0 nF capacitor. (a) Find the circuit’s impedance at 500 Hz. (b) Find the circuit’s impedance at 7.50 kHz. (c) It the voltage source has Vrms = 408 V, what is Irms at each frequency? (d) What is the resonant frequency of the circuit? (e) What is Irms at resonance?