A simply supported wood beam of length L = 16 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b = 5 in. and h = 9 in. If the allowable shear strength of the wood is 175 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. A 27 B X b h

A simply supported wood beam of length L = 16 ft carries a concentrated load P at midspan, as shown. The cross-sectional dimensions of the beam are b = 5 in. and h = 9 in. If the allowable shear strength of the wood is 175 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. A 27 B X b h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced rectangular beam with width 437.5 and effective depth 692.5 is subjected to service liveand dead loads (self-weight included) of 56 and 70.5, respectively. If required, compressionsteel bars are to be placed at a distance d′ = 692.5 from the extreme compression fiber. Use ??′ =28 ??? and ??= 420 ???. Compute the following: 1. Solve for the area of tension steel bars using ?? = 0.004.2. Solve for the area of compression steel bars using ?? = 0.004.3. Solve for the area of tension steel bars using ?? = 0.005.4. Solve for the area of compression steel bars using ?? = 0.005
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. determine 1.) a 2.) the value of fs' (actual stress of the compression bars) 3.) value of ρbalance 4.) Mu
plz, solve all the parts of this problem. Use ACI code and Solve what you have been asked. Reinforced Concrete Design-1 A fixed ended beam with span length of 24′ and cross-section of 15ʺ x 24ʺ is subjected to uniformly distributed load is shown in figure 1. Unform service dead load is 1k/ft and uniform service live load is 1.4 k/ft. Taking ?c = 3?si and ?y = 40???, a) Analyze the beam for flexure only. b) Calculate the amount of reinforcement for the given demand and check for ductility requirements. c) Detail the reinforcement using #6 bar only, and also curtail the steel ensuring development length requirements. d) Show all your calculations in the form of neat and clean drafting. Note: Your drafting must include dimensional details, reinforcement details in both longitudinal and sectional views, and cut off locations of steel.
A doubly reinforced concrete beam has a max. effective depth of 630mm and is subjected to a factored moment of 1062 kn-m (including its own weight). fºc=27.58 MPa, fy = 413.4 MPa. Use 62.5 mm steel covering. 1. Determine the width of the beam. 2. Determine the reinforcement for compression. 3. Determine the reinforcement for tension.
A floor is supported by 75mm x 200mm wooden joists spaced @ 400 mm on centers with an effective span of 3m. The total floor load transmitted to the joist is 5 Kpa. Weight of wood 6.3 KN/m3. Ew = 12x 10^3MPa. a. Determine the maximum flexural stress of the beam.b. Determine the maximum shearing stress of the beam.c. Determine the maximum deflection of the beam.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored SLAB load in Kilo Pascals? Express your answer in 2 decimal places.
A compression bar having a square crosssection with sides b 5 50 mm is subjected to load P.The bar is constructed from two pieces of wood thatare connected by a glued joint along plane pq thatis inclined at angle a 5 8 35 . The allowable stress inthe wood in compression is 11.5 MPa and in shear is4.5 MPa. Also, the allowable stress in the glued jointin compression is 3.5 MPa and in shear is 1.25 MPa.Determine the maximum load P that can be appliedto the bar.
A concrete framework is used to support a 125 mm reinforced concrete slab thatcarries a uniform live load of 12 kN/m2. The concrete density is 24kN/m3. The sizeof beam is 200 mm x 350 mm.There is a 125 mm thick brickwall on beam AD andCD. The walls are 3 m in height. Show the calculation of the design load of ColumnD in Figure 1.
A simply supported wood beam with a span of L = 22 ft supports a uniformly distributed load of w0 = 280 lb/ft. The allowable bending stress of the wood is 1.30 ksi. If the aspect ratio of the solid rectangular wood beam is specified as h/b = 3.00, calculate the minimum width b that can be used for the beam.
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3- 22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPa). fc' = 28 MPa a. determine the effective depth of the beam b. determine the depth of compression block c. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam
A 130 mm x 220 mm timber wood is used for the beam shown. Take E = 8.22 MPa. w = 8.65 kN/m, L =7. a. Compute the maximum flexural stress in MPa. b. Compute the maximum shear stress in MPa. c. Considering Agoho with Fb = 26.3 MPa and Fv = 2.95 MPa, check if the section is adequate.