A single phase a. C distributor AB 300mts long if fed from end A is loaded as under a) 100amps at 0.707 p.f lagging 200mts from pointA(b) 200amps at 0.8p.f lagging 300mts from point A. The total resistance and the Reactance and the distributor is0. 2ohms and0. 1ohms per km respectively. Calculate the total voltage drop in the distributor. The load power factors refer to the voltage at the far end

A single phase a. C distributor AB 300mts long if fed from end A is loaded as under a) 100amps at 0.707 p.f lagging 200mts from pointA(b) 200amps at 0.8p.f lagging 300mts from point A. The total resistance and the Reactance and the distributor is0. 2ohms and0. 1ohms per km respectively. Calculate the total voltage drop in the distributor. The load power factors refer to the voltage at the far end

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.52P

See similar textbooks

Similar questions

Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
Discuss the concept of power flow analysis in electrical grids and its role in maintaining system stability.
he node (busbar) and branch (line) data of a power system are provided in Table Q1.1 and Table Q1.2 respectively. All values in the tables are stated in per unit (p.u.). Using node 1 (busbar 1) as the reference (slack bus), calculate the line flows using the DC power flow method.
DISCUSS TEH ADVANTAGES AND DISADVANTAGES OF DIFFERENT TYPES COMPESATING EQUIPMENT TO TRANSMISSION SYSTEM eXPLAIN IN DETAILS
In the context of power system analysis, explain the purpose and operation of a load flow study.
16. Which of the following is a solution to the problem of circulating currents?A. Integrating the grounding circuit supplying the equipment with the equipment itselfB. Incorporating surge arresters and surge protection devicesC. Using multiple-point grounding and two power supply systemsD. Connecting the equipment frames to several reference grid structures
Discuss / Explain the operational process and show flow diagram including major equipment of a solar power plant, wind power plant, hydroelectric power plant, and biogas power plant..