Question

A strain gage located at C on the surface of bone AB indicates that the average normal stress in the bone is 3.80 MPa when the bone is subjected to two 1220-N forces P as shown. Assuming the cross section of the bone at C to be annular and knowing that its outer diameter is 25 mm, determine the inner diameter of the bone’s cross section at C.

Expert Solution

Want to see the full answer?

Check out a sample Q&A here
Blurred answer
Students who’ve seen this question also like:
Structural Analysis
Structural Analysis
6th Edition
ISBN: 9781337630931
Author: KASSIMALI, Aslam.
Publisher: Cengage,
Not helpful? See similar books
Structural Analysis
Structural Analysis
Loads On Structures. 1P
marketing sidebar icon
Want to see this answer and more?
Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*
*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.

Related Civil Engineering Q&A

Find answers to questions asked by students like you.

Q: Q3: A state of plane stress case where the normal stress is of ox , Oy and Txy shown in fig. At a…

A: The plane at which normal forces acting and shear stress is zero known as the principle stresses.…

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

A: The normal strain represents the elongation or deformation of the body that is undergone to some of…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Draw the mohr circle Sx=-160MpaSy=-85MpaSxy=45Mpa

Q: A bar of cross-section 850 mm² is acted upon by axial tensile forces of 60 kN applied at each end of…

A: Given, Cross section area = 850mm² Tensile force = 60kN Let the  direction of loading axis is x

Q: The bar shown in the Fig, has a constant width of 35 mm and a thickness of 10 mm. Determine the…

A: Click to see the answer

Q: The bar shown, with total elongation of the bar between joints A and C is 0.15 in, due to the load…

A: Given data : Total elongation between joint A and C, ∆AC=0.15 in Elongation in segment BC, ∆BC=0.117…

Q: A steel wide - flange beam has the dimensions shown in Fig . If it is subjected to a shear of V = 80…

A: Click to see the answer

Q: For the stress state shown in Fig.3., by using mohrs circle determine: - 1- the maximum normal…

A: Click to see the answer

Q: At a point on the free surface of a stressed body, a normal stress magnitude of Sy-74 MPa (T) and an…

A: σ1=185 Mpaσ1-σ22=83 Mpaσ1-σ2=166σ2=186-σ1=186-185σ2=1 Mpa

Q: Assume segments AB, BC, and CD have a circular cross section, all with constant diameter 45mm.…

A: From segment AB:∑ Fx=0FAB-24=0FAB=24KNNormal stress in AB:σAB=FABA=FABπ4d2σAB=24,000Nπ4452=15.090Mpa

Q: Direct tensile stresses of 120 MN/m and 70 MN/m' act (at a point) in a body on mutually…

A: Click to see the answer

Q: The major and minor principal stresses acting at a point in a stressed material are 80 psi…

A: Major Principal stress, σ1=-80 psi (compression) Minor Principal stress, σ2=20 psi (Tension) (a)-…

Q: At a point in a stressed material, the major principal stress is 5,000 psf compression and the minor…

A: (a) The diagram for the Mohr’s circle stress combination is shown below.

Q: Two identical plates of 55 mm wide and 4 mm thick is connected by a square pin with side dimension…

A: Maximum Tensile Stress: The maximum stress that the material can withstand is known as maximum…

Q: At a particular point in a structural member a direct tensile stress of 60 N/mm² exists on a plane…

A: Click to see the answer

Q: Two identical plates of 20 mm wide and 3 mm thick is connected by a square pin with side dimension…

A: Click to see the answer

Q: Three forces, each of magnitude P= 5 kN, are applied to the structure shown. Determine the…

A: The given data is: P=5 KN Normal stress=100 MPa

Q: Example 1: A plane-stress condition exists at a point on the surface of a loaded structure, where…

A: Given  When the element is rotated in clockwise direction through 15 degrees the stresses will…

Q: 1.42. Given the stress acting uniformly over the sides of a thin, flat plate (Fig. P1.42), determine…

A: Click to see the answer

Q: (a) Determine the state of stress resulting from the superposition of the two states shown (b) Mark…

A: To find:- a) state of stress b) mark orientation of stress

Q: In a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on…

A: Given data : σX=15 KN/cm2σY=9 KN/cm2ζXY=4 KN/cm2

Q: At a point in a stressed material, the major principal stress is 7.2 ksi compression and the minor…

A: It is required to determine the maximum shear stress. We know that, the maximum shear stress acts at…

Q: 2.3 The bar ABC in Fig. (a) consists of two cylindrical segments. The material of the bar has the…

A: Given: The axial load is 20 kN. Consider the figure,

Q: in a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on…

A: Given data in question  Normal stresses which are tensile in nature Shear stress To find out  Major…

Q: 1.42.Given the stress acting uniformly over the sides of a thin, flat plate (Fig. P1.42), determine…

A: Please refer the attached image for complete solution. THANK YOU.

Q: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average…

A: A rectangular plate ABCD is given in the figure with size 300mm by 400mm. After external stress, it…

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin of an airplane.…

A: A,B and C are arrangement of rosette  (Delta rosette)εB = εn at θ = 0°εA = εn at θ = 60°εC = εn at…

Q: At a point in a stressed material, the major principal stress is 180 kPa compression and the minor…

A: Given :σx = -180 Kpa                                                                            σy =…

Q: At a point in a stressed material, the major principal stress is 80 psi compression and the minor…

A: (a) The major principal stress is σ1 is 80 psi (compression) The minor principal stress σ3 is 20 psi…

Q: A 60 ̊ strain rosette measures the following strain at a point on the aluminum skin of an airplane.…

A: The rosette gauge is term for an arrangement of two or more rosette that  are placed closely to…

Q: 4. The bar shown in Figure 2 has a constant width of 35 mm and a thickness of 10 mm. Determine the…

A: Hello dear this is the solution of your problem The answer is found to be Maximum avg normal…

Q: Homework • A water tank 3m in diameter and 6m high is made from a steel having a thickness of 12mm.…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: in a stressed body, an elementary cube of stresses equal to 15 kN/cm? and 9 kN/cm2 are observed on…

A: Solution:-   Given  that   ⇒Tensile  stress on X‐axis, σX=15 KN/cm2   ⇒Tensile  stress  on Y‐axis,…

Q: Q2) For the beam shown in figure 2, (a) Draw the shear force and bending moment diagrams and…

A: Consider the free body diagram as;

Q: Q3 A steel wire (E=195 GPa) of diameter d=1.20mm is bent around a pulley of radius Ro= 540 mm as…

A: Stress is the force acting per unit area of an object. It can be tensile ,compressive or both.…

Q: A horizontal load Pof magnitude 96 kN is applied to the beam shown. Determine the largest distance a…

A: Given  P=96kN Maximum tensile stress= 75MPa   To Find Largest a

Q: Example 7.9 At a point in an elastic material, 0, 40 N/mm a direct tensile stress of 80 N/mm? and a…

A: To find the minimum principal stresses and maximum shear stress-

Q: in a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on…

A: Click to see the answer

Q: In a plane stress condition, the components of stress at point are ox = 20 MPa, MPa The maximum…

A: Please refer the attached image for complete solution. THANK YOU.

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A: Click to see the answer

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A: Click to see the answer

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A: Click to see the answer

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A: Click to see the answer

Q: 3. (a) A prismatic bar is subjected to an axial compressive stress of 85N/mm. Determine the i.…

A: Click to see the answer

Q: .Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: For abody to be in equilibrium following conditions have to be considered: Sum of all the forces in…

Q: force of 3500N is acting on the orange plank which is attached to the pin as shown in the figure.…

A: Click to see the answer

Q: The stresses acting on element A on the web of a train rail (see figure part a) are found to be 44…

A: This question is related to Strength of Material. In this question we calculate normal stress and…

Q: For a body under three dimensional stress state, describe the procedure for obtaining the absolute…

A: Consider a stress element on which three stress is acting:

Q: For a body under three dimensional stress state, describe the procedure for obtaining the absolute…

A: Introduction: Absolute maximum shearing stress at a given point: When a point is subjected to a 3D…

Q: naximum shear stress in a beam of rectangular cross section is 50% larger than the r cross:

A: Dear students according to our company guidelines i can answer only first question. if you need…

Knowledge Booster
Civil Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.
Similar questions
    • SEE MORE QUESTIONS
    Recommended textbooks for you
  • Structural Analysis
    Civil Engineering
    ISBN:9781337630931
    Author:KASSIMALI, Aslam.
    Publisher:Cengage,
    Structural Analysis (10th Edition)
    Civil Engineering
    ISBN:9780134610672
    Author:Russell C. Hibbeler
    Publisher:PEARSON
    Principles of Foundation Engineering (MindTap Cou...
    Civil Engineering
    ISBN:9781337705028
    Author:Braja M. Das, Nagaratnam Sivakugan
    Publisher:Cengage Learning
  • Fundamentals of Structural Analysis
    Civil Engineering
    ISBN:9780073398006
    Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
    Publisher:McGraw-Hill Education
    Sustainable Energy
    Civil Engineering
    ISBN:9781337551663
    Author:DUNLAP, Richard A.
    Publisher:Cengage,
    Traffic and Highway Engineering
    Civil Engineering
    ISBN:9781305156241
    Author:Garber, Nicholas J.
    Publisher:Cengage Learning
  • Structural Analysis
    Civil Engineering
    ISBN:9781337630931
    Author:KASSIMALI, Aslam.
    Publisher:Cengage,
    Structural Analysis (10th Edition)
    Civil Engineering
    ISBN:9780134610672
    Author:Russell C. Hibbeler
    Publisher:PEARSON
    Principles of Foundation Engineering (MindTap Cou...
    Civil Engineering
    ISBN:9781337705028
    Author:Braja M. Das, Nagaratnam Sivakugan
    Publisher:Cengage Learning
    Fundamentals of Structural Analysis
    Civil Engineering
    ISBN:9780073398006
    Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
    Publisher:McGraw-Hill Education
    Sustainable Energy
    Civil Engineering
    ISBN:9781337551663
    Author:DUNLAP, Richard A.
    Publisher:Cengage,
    Traffic and Highway Engineering
    Civil Engineering
    ISBN:9781305156241
    Author:Garber, Nicholas J.
    Publisher:Cengage Learning