Answered: A tank is filled with water through a…

A tank is filled with water through a pipe of diameter of 120 mm at a velocity of 2 m/s. Determine the velocity of water through the discharge pipe if the diameter of the discharge pipe is 150 mm.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter9: Mass And Mass-related Variables In Engineering

Section: Chapter Questions

Problem 37P

See similar textbooks

Related questions

Q: determine the Centroid of the shaded area with respect to x and y axis.

Q: The disinfection of water is carried out in a stirred tank. The treatment process has water as the i...

A: Given: The input rate is 48000 L/h. The volume of tank is 3500 L. The rate of disinfectant is 0.25/...

Q: The following data were obtained from the tensile test of Aluminum alloy. The initial diameter of te...

A: - The stress strain diagram is shown below, (a) Proportional limit, (OA) Proportional limit is th...

Q: Situation 3. Remove the 500-lb force and then determine the greatest force P that can be applied to ...

Q: Using the previous example, balance the departures and latitudes using the transit rule. CD ΙΣ DEPI ...

Q: 6.0 SUPPORT REACTIONS Example 8: Determine the reactions at A and E for the truss supporting a floor...

Q: 38. Population Dynamics Suppose that dPydt 5 0.15P(t)represents a mathematical model for the growth ...

Q: Given the ff. deflection angles of a closed traverse. Assume bearing of line AB is S 40° E.StationDe...

A: Angle Deflection Angle A 85⁰20' B 10⁰11' C 83⁰32' D 63⁰27' E 34⁰18' F 72⁰56' G 30⁰45'

Q: Q5. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown...

A: Draw the free-body diagram of the truss as follows. Write the equilibrium equation for the sum of h...

Q: Illustrate what types of basic equations and forces analysis are needed for reservoir and pipe flow.

A: Some basic equations used in pipe flow and reservoir are as follows. Continuity equation Bernoulli'...

Q: 600 lb 600 lb 600 lb D 300 lb F 300 lb B 2 ft 4 in. 6 ft A C E| H. -8 ft 8 ft 8 ft -8 ft -8 ft- For ...

Q: Write Down some applications of Vector Algebra in Civil Enginnering?

A: Vector is a quantity that has both magnitude and direction. Vector algebra has direct application in...

Q: Why do structural engineers design structures while considering different wind angles of attack, in ...

A: Asked: Why do structural engineers design structures while considering different wind angles of atta...

Q: 1: When a wood stud wall is placed on concrete or 2: Fire Protection /Fire Rating of Door & Windows ...

A: (1) The stud wall is generally placed on a bottom plate of 2 x 4 wood studs. The actual dimension of...

Q: CEN 333 Geotechnical

A: Given the results of sieve analysis for two soil samples A and B. To determine: Gradation curve

Q: A 1400-ft–long sag vertical curve (equal tangent) has a PVC at station 115 + 00 and elevation 750 ft...

A: Formula to calculate the station of PVI is as below: PVI=PVC+tangent Formula to calculate the statio...

Q: Calculate the expected peak separation when 2 peaks are resolved at a mass of 1100 and resolution of...

A: Given: Ther resolution R, is 18300. The peaks are resolved at a mass m, is 1100. The formula of reso...

Q: Normal/Dry friction. Kindly answer as soon as possible?

A: you can clearly understand if you follow the below solution

Q: An increase in pressure of a liquid from 7.5 MPa to 15 MPa results into 0.2 percent decrease in its ...

A: Given: The increase in pressure of a liquid is 7.5 MPa to 15 MPa. The decrease in volume is 0.2%.

Q: It has been estimated that a minimum run off of approximately 94 m3/sec will be available on a hydra...

A: Given: The minimum runoff is 94 m3/sec. The head is 39 m. The efficiency of the plant is 80%.

Q: . To satisfy design limitations it is necessary to determine the effect of the 2-kN tension in the c...

A: Given Data: Tension in cable, F=2 kN Angle between horizontal plane and cable, θ=20° Angle between h...

Q: Problem: A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is ...

A: The width of the beam is B=300 mm. The effective depth of the beam is d=600 mm. The modular ratio is...

Q: 3. Determine the magnitude of the counterweight W to cause the block to slide down the incline. Coef...

A: you can clearly understand if you follow the below solution

Q: 4.15 The following results were obtained from a liquid limit test on a clay using the Casagrande cup...

A: Number of blows(N) 6 12 20 28 32 Water Content (%) 52.5 47.1 43.2 38.6 37.0

Q: Grades of g = -4.500% and 92 = +2.000%, VPI station 6+300 and elevation 205.930 ft . Fixed elevation...

A: Given: g1=-4.5000%g2=+2.000%VPI station=6+300Elevation=205.930 ftFixed elevation=205.620 ft

Q: What is the minimum required length of curve assuming a design speed of 40 mph?

A: Given Data: The grades of the curve are g1=-3.50% and g2=-1.50%. The design speed for the curve is v...

Q: It is desired to determine the area of the sand bar by the indicated short offsets which were measur...

A: you can clearly understand if you follow the below solution

Q: Civil Engineering Problem 4: constant. Using unit load method find IFor the given truss all AE are W...

Q: Indicate two solid waste transfer station types that are most advantageous and write down their adva...

A: Waste transfer stations play an important role in a community’s total waste management system, servi...

Q: Solve this civil the engineering

A: Given Data: The grades of the curve are g1=-3.50% and g2=-1.50%. The design speed for the curve is V...

Q: Civil Engineering Question

A: Draw the figure.

Q: Find the weight of the snowball 1.5 m in diameter if the wet compact snow of which this ball is made...

Q: The center span of the suspension bridge shown in Fig. 50 m. The cables have been designed to resist...

A: Cable is the structure which mainly constructed to withstand the tension , the length of the cable i...

Q: CEN 333 Geotechnical

A: Given: Results of a liquid limit test done on clay using Casagrande's cup device Test Number M...

Q: Determine the vertical displacement at point C (i.e., ΔCV) for the following rigid frame, assume tha...

Q: https://www.chegg.com/homework-help/questions-and-answers/determine-force-member-truss-state-members...

A: Consider the truss shown below.

Q: · Replace the force system acting on the frame by an equivalent resultant force ind specify where th...

A: Draw free body diagram Consider the summation of forces in the horizontal direction FRX=35 sin 30o+...

Q: Еxample: 400 mm AAB =D400 mm2 %3D АВ B A E = 70 GPa AB 80 kN d Bc =10 mm ERC = 200 GPa Find d 600 mm...

A: Given Data: The area of AB portion is AAB=400 mm2. The elastic modulus of portion AB is EAB=70 GPa. ...

Q: It was determined through a survey that the rate of vehicles crossing a point on a highway is 400 ve...

A: Given: Number of vehicles crossing the point = 400 veh/h Number of vehicles expected to arrive, n = ...

Q: The shallow foundation shown in Figure 6.25 measures 1.5 m × 2.25 m and is subjected to a centric lo...

A: Given: The unit weight is 17 kN/m3. The factor of safety is 4.

Q: Draw the shear force and bending moment diagram for the following beam

A: Data given: Asked: Draw the shear force and bending moment diagram for the following beam

Q: 4. Determine the horizontal and vertical components of reaction at the pins A, B and D of the frame....

A: As per our guidelines we only solve the first question kindly resubmit the question with other two s...

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

A tank is filled with water through a pipe of diameter of 120 mm at a velocity of 2 m/s. Determine the velocity of water through the discharge pipe if the diameter of the discharge pipe is 150 mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A garden hose attached with a nozzle is used to fill a 10-gal bucket. The inner diameter of the hose is 2.0cm, and it reduces to 0.8 cm at the nozzle exit. If it takes 50 seconds to fill the bucket with water, determine the mass flow rates of water through the hose.
An open cylindrical tank having a radius of 0.34 m. Is filled with water at a depth of 0.84 m. If it is rotated about its vertical axis to a velocity of 110 rpm, what should be the height in meters so that no water will be spilled out
Water enters a pump through a 150 mm diameter intake pipe and leaves through a 200 mm diameter discharge pipe. If the average velocity in the intake pipeline is 1 m/s, calculate the average velocity in the discharge pipeline.
1. The head of water at the inlet of a pipe 2000 m long and 500 mm diameter is 60 m. A nozzle of diameter 100 mm at its outlet is fitted to the pipe. a) Determine the velocity of water at the outlet of the nozzle if friction coefficient for the pipe is 0.01.
A square tank 4 ft on a side and 10 ft high is filled to the brim with water.Find the time required for it to empty through a hole in the bottom 1 in.squared in area. The velocity of the water leaving the tank is 4.97√h ft/sec.
A fluid flows through a square conduit. At one point along the conduit, the conduit sides are 0.100 m, the velocity is 7.55 m/s, and the fluid’s SG is 0.86. at a second point, the conduit sides are 0.250 m, and the velocity is 2.02 m/s. Find the mass flow rate of the fluid.
Water enters a large rigid tank steadily at a rate of V . = 0.5 m3/s, and exits through a large rectangular opening through which the velocity changes linearly in the vertical direction from 4 m/s to 5 m/s. Knowing that the tank is full, determine the magnitude of the velocity through the circular opening at the top whose diameter is D = 15 cm.
A cylindrical tank, 1 m in diameter and 5 m high is filled completely with two kinds of liquid of equal volume. The specific gravity of one liquid is 0.8 and that of the other is 1.2. If the liquid is going out through a 75-mm-diameter orifice (with C=0.61) located at the bottom of the tank, find the time elapsed for the liquid surface to drop by 3 m.
A plastic cup, 15.0 cm in height, is filled to the rim with water and is resting on a table. A small hole is punctured in the cup at a height 9.00 cm above the bottom of the cup and is allowing water to spew out. What is the speed of the water when it strikes the table?
Determine whether the flow is turbulent or laminar if a fluid flows at 0.001?^3/? through a 100mm diameter pipe.
1. A block having a mass of 50 kg is subjected to a horizontal force that is causing it to have an acceleration of 1 m/s2. If the coefficient of friction between the block and the horizontal surface is 0.40, determine: a) the value of the horizontal force. b) Find the distance traveled after 10 seconds if it has an initial velocity of 5 m/s.
A manometer is used to measure the pressure in a tank filled with air. The fluid has a specific gravity of 0.95, and the manometer column height is 65cm. If the local atmospheric pressure is 96 kPa, determine the absolute pressure within the tank. answer in kPa abs