A truss is subjected to a 10 Kips of vertical load at G, a 30 Kips of vertical load at F and a 10 Kips of vertical load at E as shown in the figure. Calculate: (a) Forces in members AG and AB using the method of joints, (b) Forces in members FC and FE using the method of sections. Show all your calculations. This question can be answered only with a file attachment. Use only A SINGLE PDF file for your answer. Multiple file attachments are not accepted. 10 kips 30 kips 10 kips 10 ft 10 ft 5 ft 15 ft 5 ft 10 ft 10 ft 10 ft

A truss is subjected to a 10 Kips of vertical load at G, a 30 Kips of vertical load at F and a 10 Kips of vertical load at E as shown in the figure. Calculate: (a) Forces in members AG and AB using the method of joints, (b) Forces in members FC and FE using the method of sections. Show all your calculations. This question can be answered only with a file attachment. Use only A SINGLE PDF file for your answer. Multiple file attachments are not accepted. 10 kips 30 kips 10 kips 10 ft 10 ft 5 ft 15 ft 5 ft 10 ft 10 ft 10 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.5P: A vertical bar is loaded with axial loads at points B, C, and D. as shown in the figure. The bar is...

See similar textbooks

Similar questions

A space truss has three-dimensional pin supports at joints 0, B, and C, Load P is applied at joint A and acts toward point Q. Coordinates of all joints arc given in feet (see figure). (a) Find reaction force components B x, B z, and Oz (b) Find the axial force in truss member AC.
A plane truss has a pin support at F and a roller support at D (see figure). (a) Find reactions at both supports (b) Find the axial force in truss member FE.
A space truss is restrained at joints O, A. B. and C, as shown in the figure. Load P is applied at joint A and load IP acts downward at joint C. (a) Find reaction force components Ax, By, and B. in terms of load variable P. (b) Find the axial force in truss member AB in terms of load variable P.
A 150-lb rigid bar AB. with friction less rollers al each end. is held in the position shown in the figure by a continuous cable CAD. The cable is pinned at C and D and runs over a pulley at A. (a) Find reactions at supports A and B. (b) Find the force in the cable.
1.3-15 A space truss is restrained at joints A, B, and C, as shown in the figure. Load 2P is applied at in the -x direction at joint A, load 3P acts in the + - direction at joint B. and load P is applied in the + r direction al joint C. Coordinates of all joints are given in terms of dimension variable L (see figure). (a) Find reaction force components Ayand Azin terms of load variable P. (b) Find the axial force in truss member AB in terms of load variable P.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
A plane truss has joint loads P, 2P, and 3P at joints D. C, and B. respectively (see figure) where load variable P — 5200 lb. All members have two end plates (see figure For Prob. 1.8-2) that are pin-connected to gusset plates. Each end plate has a thickness/ — 0.6.2.5 in., and all gusset plates have a thickness tg= 1.125 in. IT the allowable shear stress in each pin is 12,000 psi and the allowable bearing stress in each pin is 18.000 psi, what is the minimum required diameter dminof the pins used at either end of member BE1
An elliptical exerciser machine (see figure part a) is composed of front and back rails. A simplified plane-frame model of the back rail is shown in figure part b. Analyze the plane-frame model to find reaction forces at supports A, B. and C for the position and applied loads given in figure part b. Note that there are axial and moment releases, at the base of member 2 so that member 2 can lengthen and shorten as the roller support at B moves along the 30° incline. (These releases indicate that the internal axial force N and moment M must be zero at this location
A plane frame has a pin support at A and roller supports at C and E (see figure). Frame segments A BD and CDEF are joined just left of joint 1) by a pin connection. (a) Find reactions at supports A. C. and E. (b) Find the resultant force in the pin just left of D.
A large precast concrete panel for a warehouse is raised using two sets of cables at two lift lines, as shown in the figure part a. Cable 1 has a length L1 = 22 Ft, cable 2 has a length L2= 10 ft, and the distance along the panel between lift points Band D is d = 14 ft (see figure part b). The total weight of the panel is W = 85 kips. Assuming the cable lift Forces F at each lift line are about equal, use the simplified model of one half of the panel in figure part b to perform your analysis for the lift position shown. Find the required cross-sectional area AC of the cable if its breaking stress is 91 ksi and a factor of safety of 4 with respect to failure is desired.
A long re Lai nine: wall is braced by wood shores set at an angle of 30° and supported by concrete thrust blocks, as shown in the first part of the figure. The shores are evenly spaced at 3 m apart. For analysis purposes, the wall and shores are idealized as shown in the second part of the figure. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall is assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the walls is F = 190 kN. If each shore has a 150 mm X 150 mm square cross section, what is the compressive stress