(a)-(b) A uniform ladder is 15 m long and weighs 210 N. In the figure, the ladder leans against a vertical, frictionless wall at height h = 6.5 mabove the ground. A horizontal force F is applied to the ladder at distance d = 1.6 m from its base (measured along the ladder). If forcemagnitude F = 58 N, what are (a)x-, (b)y-components of the force of the ground on the ladder? If F = 140 N, what are (c)x-, (d)y-components of the force of the ground on the ladder? (e) Suppose the coefficient of static friction between the ladder and the ground is0.38; for what minimum value of the force magnitude F will the base of the ladder just barely start to move toward the wall?(a) NumberiUnits(b) NumberiUnits

The questions are answered below

Answered: A uniform ladder is 1:

Science

Physics

A uniform ladder is 1:

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 74P: A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A...

See similar textbooks

Similar questions

A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
A horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot. (See Section 8.4.)
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.
A person carries a plank of wood 2.00 m long with one hand pushing down on it at one end with a force F1 and the other hand holding it up at .500 m from the end of the plank with force F2. If the plank has a mass of 20.0 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1 and F2?
Problems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.
A uniform ladder is 10 m long and weighs 200 N. , the ladder leans against a vertical, frictionless wall at height h = 8.0 m above the ground. A horizontal force is applied to the ladder at distance d = 2.0 m from its base (measured along the ladder). (a) If force magnitude F = 50 N, what is the force of the ground on the ladder, in unit-vector notation? (b) If F = 150 N, what is the force of the ground on the ladder, also in unit-vector notation? (c) Suppose the coefficient of static friction between the ladder and the ground is 0.38; for what minimum value of the force magnitude F will the base of the ladder just barely start to move toward the wall?
A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. The coefficient of friction between the ladder and the horizontal surface is ?1=0.195 and the coefficient of friction between the ladder and the wall is ?2=0.203. Determine the maximum angle α with the vertical that the ladder can make without falling on the ground.
A uniform plank of length 5.0 m and weight 225 N rests horizontally on two supports, with 1.1m of the plank hanging over the right support. To what distance x can a person who weighs 377 N walk on the overhanging part of the plank before it just begins to tip?
A person carries a plank of wood 2.00 m long with one hand pushing down on it at one end with a force F1 and the other hand holding it up at .500 m from the end of the plank with force F2 . If the plank has a mass of 20.0 kg and its center of gravity is at the middle of the plank, what are the magnitudes of the forces F1 and F2 ?
a uniform beam of length 12.0 m is supported by a horizontal cable and a hinge at angle u =50.0°. The tension in the cable is 400 N. In unit-vector notation, what are (a) the gravitational force on the beam and (b) the force on the beam from the hinge?
A uniform beam of length L = 2.2 m and mass M = 33 kg has its lower end fixed to pivot at a point P on the floor, making an angle θ = 15° as shown in the digram. A horizontal cable is attached at its upper end B to a point A on a wall. A box of the same mass M as the beam is suspended from a rope that is attached to the beam one-fourth L from its upper end.What is the y-component Py of the force, in newtons, exerted by the pivot on the beam? Py = Write an expression for the tension T in the horizontal cable AB. T = What is the x-component Px of the force, in newtons, exerted by the pivot on the beam? Px =