A water jet with velocity V jet impinges normal to a moving flat plate with velocity V plate such that the jet splits equally into two halves as shown in Figure. The jet cross-sectional area is 2 cm?, V jet is 20 m/s and V plate is 10 m/s and density of water is 1000 kg/m³. Consider steady flow and neglect weight of the jet, weight of the plate and frictional losses. The absolute value of the force required to keep the plate moving at constant velocity V plate is N. jet plate

A water jet with velocity V jet impinges normal to a moving flat plate with velocity V plate such that the jet splits equally into two halves as shown in Figure. The jet cross-sectional area is 2 cm?, V jet is 20 m/s and V plate is 10 m/s and density of water is 1000 kg/m³. Consider steady flow and neglect weight of the jet, weight of the plate and frictional losses. The absolute value of the force required to keep the plate moving at constant velocity V plate is N. jet plate

Name: A water jet with velocity V jet impinges normal to a moving flat plat
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A water jet with velocity V jet impinges normal to a moving flat plate withvelocity V plate such that the jet splits equally into two halves as shown in Figure.The jet cross-sectional area is 2 cm?, V jet is 20 m/s and V plate is 10 m/s anddensity o

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A horizontal water jet with a 2.5 cm diameter and a speed of V =40 m/s relative to the ground is deflected by a 60° stationary cone whose base di ameter is 25 cm The height of water along the cone is 0.125cm. Disregarding the effect of gravity and the shear forces, the horizontal force F needed to hold the cone stationary is
The cylindrical container in Fig. is 20 cm in diameterand has a conical contraction at the bottom with an exithole 3 cm in diameter. The tank contains fresh water atstandard sea-level conditions. If the water surface is fallingat the nearly steady rate dh/dt ≈ - 0.072 m/s, estimate theaverage velocity V out of the bottom exit.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find area throat, velocity in throat and temperature in throat.
A 16-cm diameter horizontal water jet with a speed of Vj = 20 m/s relative to the ground is deflected by a 40° cone moving to the left at Vc = 10 m/s. Determine the external force, F, needed to maintain the motion of the cone. Disregard the gravity and surface shear effects and assume the crosssectional area of water jet normal to the direction of motion remains constant throughout the flow.
A jet of water 3 cm in diameter strikes normal to a plate asin Fig. If the force required to hold the plate is 23 N,what is the jet velocity?( a ) 2.85 m/s, ( b ) 5.7 m/s, ( c ) 8.1 m/s, ( d ) 4.0 m/s, ( e ) 23 m/s
Suppose that there is a 4-cm water jet with a velocity of 15 m/s which hits a vertical plate with a mass on 800 kg. This plate is mounted on a track which is nearly frictionless and starts out not moving. when the jet strikes the plate, water leaves by splashing out in the plane of the plate. what is the acceleration of the plate when the jet first hits it? What is the velocity of the plate after 60 seconds? Assume that the momentum correction factor s 1.04.
A reducing elbow in a horizontal pipe is used todeflect water flow by an angle ϴ = 450from the flowdirection while accelerating it (Fig. 3). The elbowdischarges water into the atmosphere at a rate of 30kg/s. The cross-sectional area of the elbow is 150cm2 at the inlet and 25 cm2 at the exit. The elevationdifference between the centers of the exit and theinlet is 40 cm. The mass of the elbow and the waterin it is 50 kg. Determine the anchoring force neededto hold the elbow in place. Take the momentum-fluxcorrection factor to be 1.03 at both the inlet andoutlet. Density of water ρ = 1000 kg/m3, atmosphericpressure 101.0 kPa and g = 9.81 m/s2. Assumesteady, incompressible, frictionless and irrotationalflow.
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.
A tank of area A 0 is draining in laminar flow through a pipeof diameter D and length L , as shown in Fig. P4.92.Neglecting the exit jet kinetic energy and assuming thepipe flow is driven by the hydrostatic pressure at itsentrance, derive a formula for the tank level h ( t ) if it's initiallevel is h 0 .
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees.
Water enters a two-armed lawn sprinkler along a vertical axis at a rate of 60 L/s and leaves the sprinkler nozzles as 2-cm diameter jets at a 30°angle, determine the rotational speed in RPM of the sprinkler.