a. In a system an analog signal is digitized such that the sampling rate is 44.1 kilo samples/second. The peak signal power to peak quantization noise power ratio should be at least 96DB. 1. Calculate the number of quantization levels required. 2. How many bits/sample are required for the number of quantization levels calculated in part (1)?

a. In a system an analog signal is digitized such that the sampling rate is 44.1 kilo samples/second. The peak signal power to peak quantization noise power ratio should be at least 96DB. 1. Calculate the number of quantization levels required. 2. How many bits/sample are required for the number of quantization levels calculated in part (1)?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Draw a symbol for a solid-state logic element AND.
For a CD audio system, the analog signal is digitized such that the signal to quantization ratio is maintained at least 96dB. The sampling is performed at 44100Hz. a) What is the minimum number of quantization levels required to attain the given signal to quantization noise ratio?b) How many bits per sample are required when levels are identified in part a)?c) Identify the data rate in bits/s for the system.
1. a. Create the gray code representation of the following binary numbers.i) 01011 ii) 10110 iii) 01101 iv) 11001 b. If a computer’s system clock is 2.7 GHz, calculate the period of the system clock. c. What is the minimum sampling rate needed in order to successfully capture frequencies up to 60MHz in an analog signal? d. Represent the number 1.00011011101 x 2-23in IEEE Standard 754 single precision floating point binary.
If in a PCM system, uniform quantizer having total 256 steps is being used, then what will be the number of transmitted bits per sample?
For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5 kHz; (ii) Maximum decoded voltage at the receiver = ±5.01 V; (iii) Minimum dynamic range = 54 dB. (Use 2 decimal places) a) What is the coding efficiency in % b) What is the resolution in V? c) Determine the maximum quantization error in V. d) Determine the minimum sampling rate in KHz e)Determine minimum number of bits use for the PCM code excluding sign bit.
An absolute optical encoder disc has 10 rings and 10 led sensors, and in turn provides 10 bit outputs. Suppose the output pattern is 1100011100. What is the angular position of the shaft? What is the resolution?
In digital communication .explain all the methods/mechanism used for the minimization of bit error rate (BER) . Subject is Communication system.
Voice is digitized using an ADC with a sampling period of 0-1 millisecond and 10 bits/sample. What is the bit rate in kbps generated by this system ?
8- Convert the following Gray codes (1000)to binary? 9- How many bits are required to represents the decimal numbers in the range from( 0 to 999 )using : 1- straight binary code? 2-Using BCD code? 10 Determine the codes that are entered from the computer’s keyboard when the following basic program statement is typed in. also express each in hexadecimal notation.10 Add “X=A+B”;X
Binary to Octal Decoder using 7-Segment Display
Determine the sampling rate for an analog telephone signal transmitted across a single channel of a T1 line with a data rate of 256 Kbps (kilobits per second), assuming that a single sample is converted to a 16-bit integer.
Consider two microprocessors having 8-bit and 16-bit wide external data buses, respectfully. The two processors are identical otherwise and their bus cycles are the same speed. Suppose all instructions and operands are two Bytes. By what factor do the maximum data transfer rates vary? Suppose all instructions and operands are one Byte. By what factor do the maximum data transfer rates vary? Discuss your answers.