A car lot uses incandescent lamps to supply outside lighting during the night. There are three strings of lamps connected to a single 20-ampere circuit. Each string contains eight lamps. What is the largest standard lamp that can be used without overloading the circuit? Standard size lamps are 25 watts, 40 watts, 60 watts, 75 watts, and 100 watts.

A car lot uses incandescent lamps to supply outside lighting during the night. There are three strings of lamps connected to a single 20-ampere circuit. Each string contains eight lamps. What is the largest standard lamp that can be used without overloading the circuit? Standard size lamps are 25 watts, 40 watts, 60 watts, 75 watts, and 100 watts.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter2: Electrical Quantities And Ohm’s Law

Section: Chapter Questions

Problem 1PA: You are an electrician on the job. The electrical blueprint shows that eight 500-W lamps are to be...

See similar textbooks

Similar questions

The rating of a branch circuit is based on (Circle the correct answer.) a. the rating of the overcurrent device. b. the length of the circuit. c. the branch-circuit wire size.
A car lot uses incandescent lamps to supply outside lighting during the night. There are three strings of lamps connected to a single 20 ampere circuit. Each string contains eight lamps . What is the largest standard lamp that can be used without overloading the circuit? Standard sizes lamps 25 watts , 40 watts , 60 watts 75 watts ,and 100 watts
Acar lot uses incandescent lamps to supply outside lighting during the night. There are three strings of lamps connected to a single 20-ampere circuit. Each string contains eight lamps. What is the largest standard lamp that can be used without overloading the circuit? Standard size lamps are 25 watts, 40 watts, 60 watts. 75 watts, and 100 watts.
A hardware store measures 90ftx110ft. A portion of the building 80ftx40ft is used for storage. The remainder of the building is used as showroom. There is a total of 45feet of show windows, and there is one outdoor sign. What is the total lighting load for this building?
Answers for calculated individual voltages Topic: the voltage divider circuit.
There are 32 solar cells in the solar system, and each one has the qualities listed below: Voc is set at 0.75 volts, while Isc is set at 2 milliamperes. Open circuit voltage and short circuit current will be if all four cells are in series and the groups are linked in parallel.
29 what is the name of the circuit d) none
What voltage would a code of 190 belong to on a step of 3.9mV?
An electrician has two two-way switches (H-I-J and C-D-E in the diagram), a light bulb, and a power source. How should she connect the terminals so that either switch can be used to turn the light on or off? Draw the circuit diagram
Two lamps x and y are hanged at a distance 12 ft between their centers, Lamp x gives 140 cp and 7 ft above the working space while lamp y gives 200 cp and 5 ft above the working space. At what distance from a point directly below lamp x on the line joining their centers will the two lamps give equal amount of illumination
The AC electricity has a source of voltage rated 240 volts with four electrical appliances rated 1500 watts, 1000 watts, 1300 watts, 2000 watts and it is connected in series. Identify the most economical wire size you must use in this circuit.
To answer the question, type your answers in RED or paste the image of your handwriting solution Given the circuit #1 presented above, answer the following questions: Determine the value of the VD (voltage forward of the LED) for the LEDs RED, VDRED, GREEN, VDGREEN and BLUE, VDBLUE, when the current through the LEDs is 10mA, VDRED = ____________ ; VDGREEN = ____________ ; VDBLUE = ____________ Is the LED in Circuit #1, connected in the way that will be lighting up or not – Justify your answer Type your answer here Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Type your answer here or paste the image of your handwriting solution here Calculate the value of the resistance Rled in Circuit #1, to ensure that…