Question

Air at 800 kPa and 400°C enters a steady-flow nozzle with a low velocity and leaves at 100 kPa. If the air undergoes an adiabatic expansion process through the nozzle, what is the maximum velocity of the air at the nozzle exit in m/s?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Fluid Mechanics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: The jib crane supports a load of 750 lb from the trolly which rides on the top of the jib. Determine...

A: Click to see the answer

Q: Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical res...

A: Given: The diameter of pipe = 1 cm The height of cylindrical reservoir = 20 cm The height of the pip...

Q: 18-41. The spool has a mass of 20 kg and a radius of gyration of ko = 160 mm. If the 15-kg block A i...

A: Given that: The mass of the spool m=20 kg. The radius of gyration is K0=160 mm The angular velocity...

Q: Why is work done a scalar quantity?

A: Physical work is obtained as dot product of force and displacement. Since force and displacement are...

Q: A mass of 15 kg of air in a piston–cylinder device is heated from 25 to 95°C by passing current thro...

A: The flow of electricity is considered as the work done on the system. The enthalpy change of the gas...

Q: The rigid L-shaped member ABF is supported by a ball-and-socket joint at A and by three cables. For ...

A: Consider the free body diagram shown below for the given member.

Q: A 400-lb vertical force is applied at D to a gear attached to the solid 1-in. diameter shaft AB. Det...

A: Click to see the answer

Q: It is an embedded support at point A of the beam, whose loading status is given below. Find only the...

A: Click to see the answer

Q: A particular frost-free refrigerator uses about 745 kWh of electrical energy per year. Express this ...

A: Click to see the answer

Q: Argon is compressed in a polytropic process with n = 1.2 from 120 kPa and 10°C to 800 kPa in a pisto...

A: Given: The initial pressure of the argon in the piston-cylinder device is P1=120 kPa The final press...

Q: A piston–cylinder device contains 2.2 kg of nitrogen initially at 100 kPa and 25°C. The nitrogen is ...

A: Given, Mass of Nitrogen (m) = 2.2 Kg P1 = 100kPa T1 = 25°C=25+273=298K PV1.3 = Constant    

Q: You are part of a team working in a machine parts mechanic’s shop. An important customer has asked y...

A: Click to see the answer

Q: A steel penstock has a 750-mm outer diameter, a 12-mm wall thick-ness, and connects a reservoir at A...

A: Given data: Outer diameter of penstock, d0 = 750 mm Thickness of the penstock, t = 12 mm Density of ...

Q: Show that the volume expansion coefficient of an ideal gas is B=1/T, where T is the absolute tempera...

A: Assumption Pressure is constant ( P = C )   We know that change in volume due to thermal expansion i...

Q: Gear A has a mass of 1 kg and a radius of gyration of 30 mm; gear B has a mass of 4 kg and a radius ...

A: Write the given data:

Q: Using a handheld bicycle pump to generate an air jet, a soda can as the water reservoir, and a straw...

A: The atomiser can be designed by using a handheld bicycle pump, a soda can and straw. The handheld bi...

Q: Determine the vertical displacement of point C of the A992 steel beam. I = 80(106) mm4.

A: Given data: *The moment of inertia of the steel beam is I=80×10^4 mm4. *The young’s modulus of the A...

Q: For the beam and loading shown, determine the range of the distance a for which the reaction at B do...

A: Assuming reaction RB positive when directed upwards Taking net moment about D  

Q: The 60° strain rosette is mounted on the surface of the bracket. The following readings are obtained...

A: Write the given data:  

Q: Consider a well-insulated horizontal rigid cylinder that is divided into two compartments by a pisto...

A: The mass of the helium gas can be determined as, The mass of the Nitrogen gas can be determined as,

Q: Water flows at 15 f/s through a 6 ft wide rectangular channel as shown in the figure. The upstream d...

A: Given: Width of the channel B = 6 ft Discharge in the channel Q = 15 ft3/s   The value of discharge ...

Q: Water is flowing through a 10-cm-diameter water pipe at a rate of 0.1 m3/s. Now a diffuser with an o...

A: Given: The of pipe at the section of bolt, d = 10 cm The diameter of the pipe at the exit, D = 20 cm...

Q: A 3-m long and 0.4-cm-thick cast iron (k= 52 W/m ·°C) steam pipes of outer diameter 10 cm are connec...

A: Given data

Q: Consider a typical centrifugal liquid pump. For each statement, choose whether the statement is true...

A: (a) At the point of maximum volume flow rate (V̇), the net head of the pump will be zero since the n...

Q: The cloth shroud from around a mummy is found to have a 14C activity of 9.7 disintegrations per minu...

A: Given: The half time for decay, t1/2 = 5715 yr The disintegration per minute per gram of carbon, N =...

Q: A 25 MVA turbo-alternator is working on full load at a power factor of 0·8 and efficiency of 97%. Fi...

A: Given data Power of turbo alternator P = 25MVA Power factor of the alternator 0.8 Efficiency of the ...

Q: An 8-kg cylinder C rests on a 4-kg platform A supported by a cord that passes over the pulleys D and...

A: Given data as per the question mass of block A = 4 kg mass of block C = 8 kg mass of block B = 4 kg ...

Q: Describe the normal pedal feel when the ABS is activated during hard braking?

A: Anti braking system(ABS):  Anti braking system(ABS) allows a driver to apply the brakes  quickly whe...

Q: What is the internal axial force?

A: Internal Axial Force is defined as the force acting in the direction parallel to the axis of the mem...

Q: 1. A particle is displaced 60cm toward the north and is then given a second displacement of 90cm dir...

A: Since you have asked multiple questions in a single request we would be answering only the first que...

Q: Determine the mean effective pressure of an ideal Otto cycle that uses air as the working fluid; its...

A: Given Data: The pressure at the inlet is: P1=14 psia The temperature at the inlet is: T1=60 0F The ...

Q: Disk A has a mass mA = 4 kg, a radius rA = 300 mm, and an initial angular velocity ω0 = 300 rpm cloc...

A: Disk A Mass = 4 kg Radius = 300 mm Angular velocity = 300 rpm clockwise Disk B Mass = 1.6 kg Radius ...

Q: Explain Managing Constraints in Line Processes?

A: The constraints can be managed in a line process using the following five steps: First, the problem...

Q: *14-76. The spring has a stiffness k = 50 N/m and an unstretched length of 0.3 m. If it is attached ...

A: Given Data: The stiffness of the spring is k = 50 N/m. The unstretched length of the spring is t = ...

Q: Determine the magnitudes of the projected components of the force              F = [60i + 12j - 40k]...

A: Given data: Force, F = 60i + 40j – 12k   Writing the positions of point A,B and C, in vector form, ...

Q: Air in an ideal Diesel cycle is compressed from 2 to 0.13 L, and then it expands during the constant...

A: Given: The volume of the air in an ideal diesel cycle before compression is V1=2 L The volume of the...

Q: The reservoirs in Fig. contains water at 208C. If thepipe is smooth with L = 4500 m and d = 4 cm, wh...

A: The temperature of the water in the reservoir is T=208 C. The length of the pipe is L=4500 m. The di...

Q: 4-14. The man uses the hand truck to move material up the step. If the truck and its contents have a...

A: Given data: The truck and its contents have a mass is m=50 kg. The centre of gravity is G. Apply e...

Q: A pipe of diameter 60 mm is gripped by the stillson wrench shown. Portions AB and DE of the wrench a...

A: Draw the free-body diagram of section ABD. Draw the free-body diagram of the pipe. Draw the free b...

Q: For the given loading, determine the zero-force members in the truss shown.

A: In this problem, the member FG is attached with member EH without any force so it will be a redundan...

Q: On both P-v and T-s diagrams, the area enclosed by the process curve represents the net work of the ...

A: The net work of the reversible process is represented by; Here, the term ∫Pdv represents the area e...

Q: The cable has a specific weight g (weight/volume) and cross-sectional area A. Assuming the sag s is ...

A: Given Data: Weight per volume of the cable is: g (weight/Volume)